On an enclosed machine a cutout slug that tips once cut free can stand up
above the sheet and catch the enclosure door when the pallet changes. The
head already keeps off cut cutouts, so this is about clearing the door, not
the head.
Cutting Settings > Cutouts > "Slice slugs the support grid can't hold
level" (CuttingParameters.SliceTippingSlugs, off by default, saved per
machine thickness and written only when on) makes Plan Cutting cut each
such slug along the bed's contact lines (grid rows and columns, slat center
lines) before the cutout, so no piece keeps a contact and the pieces drop
between the supports. Each slice stops a kerf short of the cutout, so the
pieces stay attached until the cutout's own kerf frees them together. A
slug the bed holds level, or one on no contact, is left whole; a cutout
holding another part or another of its part's cuts is never sliced.
Slices are break cuts emitted right after the drawing's own break cuts,
pierced on themselves and led straight back to their start. The
released-contour proof now leaves out straight break cuts lying wholly
inside one of the part's closed holes, since the grid cells they free are
scrap; break cuts in material still take part. The plan fingerprint only
changes when the setting is on.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Geometry, nesting and import code now call PortableMath instead of
System.Math for Sin, Cos, Tan, Atan, Atan2, Asin and Acos (Core, Engine,
IO, Data; 269 calls in 64 files). A test fails if those projects call the
runtime's trig again.
With the runtime's trig, Windows and Linux disagreed in the last bit at
non-quarter angles and the same job could nest differently: the
learned-angle nests (a cross fixture) placed 23 parts in Strip on Windows
and 28 on Linux. Now every Engine.Tests pin gives the same layout on both
(3600 passing on Linux and on DesktopPC), Linux layouts are unchanged, and
the learned-angle rows are re-pinned to the shared layouts, which pass the
overlap and work-area checks, and run on every platform again.
Fixes Project Memory 518f3b58.
The part cut first no longer makes a separate uncompensated centerline
cut with its own lead-in and lead-out, then re-pierces for its
remainder. It cuts its outside compensated, which puts its shared edge
on the kerf centerline, starting on the common line: a straight lead-in
from the scrap along the shared edge, then the line and on round its
perimeter with no lead-out. A member with spans already cut stops in
that kerf and cuts its last stretch from it, ending beside the part it
is cut before. Partners still cut only their remainders.
Replay's tabbed-ring accounting now accepts pieces that tile each span
exactly once, and the pre-post review counts a span as cut by a
member's compensated edge (or an older centerline cut).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Straight spans of one pair that meet at a corner chain into one shared
path (CommonLineGeometry.Paths). Plan Cutting cuts it as one open
centerline cut through its corners, pierced and left in scrap along its
end legs; each member's spans run on to its own vertex at a corner, so
the path is one tab run. Join Common Line slides along the main edge so
the step of a Z or L also lands one kerf apart, and the plate draws the
path through its corners.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
N26-295's PT42 pairs saved spacing in slice 1 but every shared edge was
still cut twice, costing a pass per edge and risking a freed part
tipping under the head on the second pass.
Plan Cutting now cuts a plate's common lines once unless the plate is set
to cut them twice. Each group is cut member by member, owner before
partner (a captured dependency that search and replay enforce, so a kept
order cutting the partner first is a constraint conflict): the member's
holes, then the shared cuts it owns as open CommonLine centerline cuts
entered through the notch on the span's axis, then its remainder pieces,
each ramped in from the kerf the shared cut opened. Capture marks the
shared spans as tabs on the owned clean copy, so replay's contour
accounting proves each perimeter is cut exactly once; a lead that fits
at neither end refuses as UnsupportedGeometry naming the span, never
shortened. Material still comes from the drawing, so utilization,
quantity and overlap results do not change. Members are never
support-tabbed; locked or excluded members and broken groups refuse.
The CI Fiber post writes shared cuts in the cut-off form with a lead-in
and no G41/G42, and remainders in the contour form on their perimeter's
compensation side, named by a remainder comment. Cincinnati CL (whose
PreApplied mode offsets nothing) and Gravograph refuse such nests, as do
the desktop and console for any post without ICommonLinePostProcessor;
nothing falls back to a silent double cut. Plate > Arrange > Cut Common
Lines Twice keeps slice 1's behavior, persists with the plate and makes
an open plan stale.
Pre-post review now checks each span is cut once, on its centerline, by
the member cut first, and the rapid check treats a finished member's
remainders as an obstacle. Compensation start in void and cancel in
kerf are unconfirmed on the CI FIBER 4020; release waits on a 3/16
stainless coupon trial.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A cutout's lead-out ends in its slug, so the rapid after it always crossed
the cutout just cut and the strict search refused every plan with cutout
lead-outs. The slug is free and may drop or tip, so emission now marks that
rapid to raise the head, and the rapid check accepts a raised rapid that
starts at the lead-out's end and leaves its cutout exactly once. Cutouts
without a lead-out, or with an overcut, still leave from the cut head down.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A tab entered at a fillet joint trims back around the corner, so the cut
stops on one edge and starts on the other. Each straight lead took its own
edge's normal and the pair sat 150 degrees apart, reading as one bent line
through the corner. Both now take the bisector of the two ends' normals and
form the same V they form on a straight edge, falling back to their own
normals when either lead would not clear the part.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A tabbed outside cut is trimmed short of its entry, but the trim only
handled lines and arcs: a round part's outline is one circle, so it was
cut whole. Plan Cutting counted it as tabbed and called the plan ready,
then the pre-post review found no tab and warned that the part may tip.
Cut a tabbed circle as an arc that stops the tab's chord short of its
entry, travelling the circle's own way.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
With a pierce diameter set, every internal contour whose configured
pierce is inside the zone is resolved by flattening the cutout, finding
its pole and eroding it, and the search emits a part's whole chain again
on every expansion, so on parts with dozens of such holes almost all of
the planning time went there: three 1,600-motion parts took 41 minutes
and timed out in production. The resolution is a pure function of the
hole, the entry, the configured lead-in, the zone and the turn, so each
preparation now keeps it by contour ordinal and reuses it, unchanged,
across its emissions and copies. The same plate plans in 148 s.
Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
The repo mixed variants such as center/centre and color/colour, so a
name could be spelled either way and searches missed half the hits.
Standardize on the US spelling, matching .NET's own APIs (Color, Center).
Wire values owned by other systems keep their spelling: the material
ledger's "Cancelled" hold status and GitHub's "cancelled" job status.
No behavior change beyond the spelling of a few status messages.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Small features got leads that ignored their shape: full 0.15 leads at a
shallow angle along letter strokes, stubs at the pierce zone's edge in
round holes that could be pierced in the middle, and a lead aimed at a
letter's far pole that ran longer than configured.
Plan Cutting now limits a lead to the feature's depth at its entry, where
a second wall becomes as near. The pierce-zone fallback goes there first
and otherwise aims beside the entry rather than at the whole cutout's
pole. Pinned contours keep their leads, and wide cutouts are unchanged.
Centred pierces exposed the line/circle tangent test: its absolute
discriminant tolerance called a radial line through a hole under about
0.056 radius tangent, reporting a false contact at the centre. Tangent
now also requires the line to stay at the rim, which keeps true grazes
as they were.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Plan Cutting ranked a convex corner first, but a corner rounded by a small
fillet had no corner vertex: its tangent joints ranked level with straight
edge midpoints, so travel decided and a large part (P230323-02 plate 8,
PT06, 0.015 corner fillets) started in the middle of a 64-inch edge. A start
there can leave a step where the cut closes after the head has put heat into
the plate; at a corner it is hidden.
A convex fillet tangent to straight edges at both ends, turning less than a
half circle and reaching no further along either edge than its length, now
makes its two joints convex-corner entries. Each carries its reach from the
sharp corner it rounds, so ranking counts it on both sides of that corner.
Longer curves, half-circle ends and inside fillets keep their tangent joints.
Every perimeter on that plate now starts at a corner; the problem-nest corpus
has no plate below its baseline.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Small text and narrow slots often have no entry where the configured
lead-in fits, so Plan Cutting refused them. When every entry of a cutout
fails, the planner now erodes the cutout inward (to the pierce clearance,
or nine tenths of its inscribed radius when smaller), pierces at the
eroded point nearest each ranked entry and leads straight to the closest
wall, with no lead-out. Letter strokes pierce on their centre lines; a
tapering feature pierces at its widest spot. The lead validator still
checks every candidate, and cutouts whose lead fits are unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Curved leads turned with the contour winding, which is backwards on outside
perimeters: arc lead-ins arrived against the cut, and Line + Arc / arc
lead-outs went the long way round on one winding. LeadTurn now gives the
arc's turn direction for emission, the pierce-zone check and the preview,
and the arc geometry mirrors with it.
At convex outside corners, curved lead-ins use the first-cut edge's normal
and arc lead-outs the last-cut edge's, whichever edge was picked.
ArcLeadIn gains SweepAngle (degrees, (0, 180], default 180) in the cutting
panel, settings, nest files and cut pins; older files read as 180.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Master already starts such entries exactly at the vertex (45592a81), so the
cherry-picked snap was redundant and its test's off-vertex precondition no
longer holds.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Full circles now take InternalLeadIn/InternalLeadOut like every other
cutout; the ArcCircle lead settings and the cutting panel's Arc / Circle
tab are removed. Circle-specific geometry handling (radius clamp, angle
rounding, pierce zone) is unchanged.
Older nest files and desktop settings still load: their arcCircleLeadIn/
arcCircleLeadOut keys are ignored and no longer written, so re-planned
circles take the internal leads. Saved part programs are untouched.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A closest-point entry within Tolerance.Epsilon of a line or arc vertex made
ReindexAt start the contour at the vertex while the lead-in still ended at
the off-vertex point, so the cut closed short of its start and replay refused
the whole plate. Snap such entries onto the vertex before emitting the lead-in.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Place Lead-in built its contours from cut-layer entities only, so on a
blank the largest cutout looked like the outside and took an external
lead pierced on the blank; committing then regenerated the part with the
outline as a cut perimeter. The legacy whole-part strategy did the same.
Both strategies now refuse a program with a display perimeter and leave
the part unchanged, and Place Lead-in explains that such a part's cutouts
get their leads from Plan Cutting instead of selecting it.
An applied cutting program for a display-perimeter blank held only its
cutouts, so the part shrank to them: a 30 x 20 door reported an 11.5 x 20
extent, overlap and the plate view lost the blank, and running automatic
cut-offs afterwards added lines straight through it.
A complete emission now ends with a display tail: a marker comment, a
rapid to the outline and the outline on the display perimeter layer. The
part keeps the blank's bounds and material, so later cut-offs still have
nothing to cut and the door plans again as before. Nothing executes the
tail: executed reads stop at the marker, so search, replay and the
pre-post review see only the cuts, and cut time, the rapid display and the
cut simulation leave it out. DisplayPerimeterTail.ForPosting gives posts
the program without it and refuses an unplanned display perimeter.
Some jobs cut only cutouts into a supplied blank, such as instrument holes
in a purchased door that is the whole sheet. Its outline has to be known
to the planner (the blank is material that leads, rapids and cut-offs must
respect) but must never be pierced, led or cut.
A new DisplayPerimeter layer marks that outline. It is material, so
nesting, containment, lead clearance and automatic cut-offs all see the
blank; a door that fills its sheet leaves cut-offs nothing to cut. Cutting
preparation keeps it out of the contours entirely: with no cut perimeter
every contour is a hole with internal leads, and the search, best-effort
and safest-route paths stop offering a perimeter. Replay refuses any run
along the display perimeter and completes once every other ring is cut.
A display perimeter must be one whole closed contour enclosing every other
contour; a mixed ring, one inside another contour, or a second one is
refused with that reason. Saving, drawing and posting it are still to do.
With a pierce diameter set, a perimeter none of whose configured lead-ins keeps its pierce
clear (a lead shorter than the zone radius, or neighbours closer than it) was only rejected.
Plan Cutting now looks for a pierce in the open scrap around the part instead.
- ScrapPierceSearch (Engine): the window four zone radii around the part, minus every nearby
part's clean material grown by the zone radius and a margin (ClipperBridge, conservative
flattening); the clear point nearest each ranked perimeter entry is a candidate. Other
parts' cutouts count as scrap, the part's own holes do not. With no clear scrap, the
PolyLabel pole of the free scrap is the best effort, and its shortfall is reported.
- ContourChoice.Pierce / PreparedContours.ScrapPierceEntry: the planner's choice carries the
pierce; the emitter cuts a straight lead from it to the nearest perimeter point and still
reads nothing but the contour and the choice.
- Every candidate passes the lead validator like any planner-chosen entry; pinned perimeters
keep their pins and warn. Without a pierce diameter nothing changes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Thick plate pierces leave a crater wider than the kerf. CuttingParameters.PierceDiameter
(Cutting Settings > Pierce Diameter, 0 = off) requires every lead-in pierce to keep half
of it from all part material: its own contour, its holes and every other part.
- LeadPathValidator checks the zone during Plan Cutting candidate checks and final
replay; fixed emissions warn as usual. No-fit findings explain the zone.
- PierceZoneReview reports Pierce zone warnings before posting for leads from any source.
- Holes whose configured pierce is inside the zone move it toward the hole's PolyLabel
pole (round holes: the centre), as close to the contour as the zone allows; a hole
too small for the zone is pierced at its pole and the shortfall is still reported.
- Straight corner leads and round-hole clamping use the larger of PierceClearance and
the zone radius. The manual lead-in preview shares the Core rules.
- Persisted through the DTO, owned copies and state fingerprint.
Perimeter fallback is not included; see docs/geometry/pierce-zone.md.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A converted outline whose seam closes within the admitted 1e-6 gap could
only be entered at its seam: entered anywhere else, the arc after the
seam started off its own circle and every emission was refused as an
inconsistent radius. The search then spent its whole budget on that
part and the plate never planned. Emission now bridges the gap with a
straight move and cuts the arc as drawn; the verifier already admits
that slack. An entry on the seam vertex is left as before.
Each prefix of a part re-checked its earlier contours' leads against
every other part's material. One search now remembers each verdict by
the lead curve's exact bits and the material's reference, charging the
same native query budget; replay never uses it. On the reported plate
the memo alone gives a byte-identical result in 57 s instead of 12 min 47 s;
with the seam fix the plate plans Ready in about 17 s.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A hole can now be declared a tabbed cutout in the CAD Converter: pick a
circle or any edge of a closed hole, set the tab count and width, and drag
the tabs around the hole. The definition persists on the drawing and in the
nest file, and stays editable from the source entities.
The builder replaces the hole with open cut pieces and uncut spans on a new
Tab layer. Tabs are material, so area, nesting and overlap checks still see
a closed hole, but they are never cut. Plan Cutting and Assign Lead-ins cut
each piece from the slug with the internal lead-in and no lead-out. A lead
that would reach back over a tab is mirrored, and an arc lead onto an arc
pierces straight in. Planning accounts for each span between tabs and runs
the open-cut proof, so its own tabbed cutouts certify; tabs followed by a
lead-out are still refused. Pre-post review flags programs that still
contain tab motions.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Breakoffs are now picked by their joining line, default to the smaller side as scrap
(flippable), and cut that line between tabs on a new Break layer instead of slots.
Plan Cutting and Assign Lead-ins enter each cut from the scrap with the nest's internal
lead-in, or pierce on the line without one; checks treat break cuts as intentional open
cuts that are not material.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
PreparedContours.Capture(program, parameters, pins) takes CutPinResolver
results for the same contours and fixes every resolved pin's contour: its
one and only entry is the pin's point, and it is emitted through the
existing emitter with the pin's own lead-in, lead-out and tab (angle
rounding off, so the entry never moves). Every catalogue returns the pinned
entry alone and emission refuses any other entry for that contour, so no
search path can relocate it. The certified tab size is the pinned outside's
own, so a pinned tab gap is genuine and replay certifies it. Unpinned
contours keep the shared settings and automatic selection; without pins the
existing preparation is untouched (5.1 digests unchanged).
Capture now resolves a regenerated part's drawing pins. A pin that does not
resolve (not on a contour, on several, sharing one, or unplaceable) is never
guessed: its contour stays automatic and the plate gets a FixedLead warning
naming the pin, making the proposal UNVERIFIED. A tab pinned on an internal
contour cannot be cut as pinned (only the outside is tabbed) and warns the
same way. Pins-off, locked parts with pins and freshness follow in 5.4.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
EmitCandidateForValidation emits exactly one owned contour with its
normal lead-in and lead-out and its ORIGINAL contour type — the
perimeter keeps External even with no holes before it — through a small
shared EmitChosenContours seam, so a perimeter candidate's emitted leads
can be validated before the hole choices exist. The probe is a throwaway
program: never installed on a Part, never a complete plan. Normal Emit
and EmitPrefix keep the perimeter-last gate untouched (still throwing
for Emit([perimeter]) on a holed part); foreign and re-stamped choices
still fail ownership/geometry validation and source shapes/settings are
never used directly. Differential tests pin per-contour block fidelity
(External-vs-hole lead geometry, five lead styles, two hole
choice/orders, scribes once, reversed winding, rotated capture, circle
rounding/clamping without cross-contour state) — contour lead geometry
is choice-independent, only absolute accumulated coordinates drift by
ulps with program head.
Expose TryClassifyAutomaticStartCorner: an internal read-only query over
the emitter's existing TryGetCorner/ClassifyCorner with the same winding
derivation EmitContour uses, so start-point planning can prefer convex
corners without copying tangent math or touching lead generation. Corner-
kind characterization covers convex, reflex, tangent-smooth and cusp
vertices from either adjacent edge, both windings, under rotation, and
rejects midpoints and open contours.
A tab trims the perimeter short of its entry, but the lead-out was still
generated from the nominal entry point. An arc lead-out therefore started
off its own radius (ExecutionMotionReader rejected it as inconsistent), and
a line lead-out ran diagonally back toward the entry.
Every lead-out style on a tabbed perimeter now leaves from the trimmed
cut's actual end, on that entity's normal, so arcs are tangent and the tab
gap stays uncut. Untabbed contours and the corner run-out rules are
unchanged. Malformed legacy output is still refused, never refit.
Red before the fix: the three tabbed arc cases threw "Arc has zero or
inconsistent radius" and the line case ended at y=5 instead of 4.8. Keeping
the entry's normal at the actual end fails the curved-perimeter case.
A straight lead-in at a convex outside-perimeter corner now runs along the
extension of the edge cut first, so the torch enters on that line and keeps
cutting it. The result no longer depends on which of the corner's two edges
auto-assign or the manual cursor picked, which made placement flip between
straight and 90 degrees. The approach angle is ignored at such corners.
The straight lead falls back to the first-cut edge normal when its pierce
would be closer than PierceClearance to the contour (very flat or tessellated
corners). Reflex perimeter corners bisect the notch. Line lead-outs run on
straight past a convex corner along the last-cut edge, except on tabbed
perimeters. Program generation and the Place Lead-in preview share
ResolveLeadIn/ResolveLeadOut.
Repo-wide sweep with the pinned CSharpier 1.3.0 tool. Whitespace and
line-wrapping only; OpenNest.Engine.Tests (109) and OpenNest.IO.Tests
pass after reformat, full solution builds 0 errors.
Added .csharpierignore so csproj/config XML keeps its existing layout
(CSharpier's XML wrapping churns attributes with zero benefit).
Formatting is now enforceable: dotnet csharpier check . passes.
Tabs were being applied to internal cutouts and circle holes, which is
incorrect — only the external perimeter should be tabbed. Restructured
the Tabs panel to use radio buttons ("Tab all parts" vs "Auto-tab by
smallest dimension") so the two modes are clearly mutually exclusive
instead of the confusing implicit override behavior.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Open (non-closed) shapes like scribe lines or partial cuts don't have
a meaningful pierce point or closing segment, so applying lead-in/out
would produce invalid toolpaths. Skip the lead-in/out logic and emit
them as raw contours in both Apply and ApplySingle paths.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Snaps lead-in angles on ArcCircle contours to a configurable
increment (default 5°), reducing unique hole variations from
infinite to 72 max. Rounding happens upstream in EmitContour
so the PlateView and post output stay in sync.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
External lead-ins now sit on the line between the last internal cutout
and the next part's first pierce point, minimizing rapid travel. Cutout
sequencing starts from the bounding box corner opposite the origin and
iterates 3 times to converge the perimeter lead-in and internal sequence.
LeadInAssigner and PlateProcessor both use a two-pass approach: first
pass collects pierce points, second pass refines with next-part knowledge.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
FilterPanel.LoadItem was hardcoding all layer and line type checkboxes
to checked, ignoring actual visibility state. Now reads Layer.IsVisible
and entity IsVisible to set correct checked state.
Also guard DetermineWinding against shapes with fewer than 3 polygon
points (defaults to CCW) to prevent crash when applying lead-ins.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Adds ApplySingle to ContourCuttingStrategy that applies lead-in/out to
only the contour containing the clicked entity, emitting other contours
as raw geometry. Also adds ApplySingleLeadIn wrapper to Part.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Shape.Area() returns Math.Abs(signedArea), so DetermineWinding always
detected CCW regardless of actual winding. Use ToPolygon().RotationDirection()
which uses the signed area correctly.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
ComputeNormal assumed CW winding for all contours. For CCW-wound cutouts,
line normals pointed to the material side instead of scrap, placing lead-ins
on the wrong side. Now accepts a winding parameter: lines flip the normal
for CCW winding, and arcs flip when arc direction differs from contour
winding (concave feature detection).
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Resolve lead-in points by walking backward through cutting order (from
perimeter outward) so each lead-in faces the next cutout to be cut
rather than pointing back at the previous lead-out. Extract EmitContour
and EmitScribeContours to eliminate duplicated cutout/perimeter logic.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
CCW arcs (e.g. the top of a U-slot) had the radial normal pointing
into the part material instead of into the scrap. This caused the
lead-in preview to flip sides on concave features.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
When TabsEnabled is set, trims the end of each contour using a circle
centered at the lead-in point with radius equal to the tab size. The
uncut gap between the trim point and the contour start keeps the part
connected to the sheet.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Scribe/etch lines were being treated as cut contours by
ContourCuttingStrategy, receiving lead-ins and kerf compensation.
Now they are separated before ShapeProfile construction and emitted
as plain moves with LayerType.Scribe preserved.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Scales down lead-ins that would place the pierce point too close to the
opposite wall of small holes. Uses quadratic solve to find the maximum
safe distance inside a clearance-reduced radius. Adds Scale() method to
all LeadIn types and applies clamping in both the strategy and the
interactive preview.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Three issues caused incorrect rendering after lead-in application:
- Rapid move entities from ToGeometry() were included in ShapeProfile
contour detection, turning traversal paths into cutting moves
- Program created with Mode.Incremental default made the absolute-to-
incremental conversion a no-op, leaving coordinates unconverted
- AddProgramSplit didn't call StartFigure() at rapid moves, causing
GraphicsPath to draw implicit connecting lines between contours
- Part.Rotation returned 0 from the new program instead of the actual
rotation, displacing the sequence label on rotated parts
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Restructure the cutting parameters dialog with separate Lead-In and
Lead-Out GroupBoxes per tab, exposing editable length/angle/radius
fields for lead-outs (previously hardcoded). Add Tabs section with
enable checkbox and width control. Also fix lead-in/lead-out angle
calculations and convert cutting strategy output to incremental mode.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>