With support tabs on and no support bed, nothing was tabbed and nothing
said so. A new no-bed width range (NoBedTabMinWidth..NoBedTabMaxWidth,
the short side of the part's minimum-area bounding rectangle) now picks
the parts to tab instead. SupportTabSettings.Analyze makes the choice
for Plan Cutting, hand-placed lead-ins and the pre-post review; without
a bed any tab clear of inside corners counts. With no bed and no range,
the plan notes that nothing was tabbed. Cutting Settings > Tabs gains
the range fields, and the values persist with the cutting parameters.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
NestLayoutCheck rejected Fill layouts whose interlocked arcs sat exactly
at the part spacing: its SpacingOutline circumscribes arcs by up to 0.001
each, more than the 0.0005 slack, so facing arcs overlapped. The runner's
placement validator measured inscribed 0.001 polygons instead and so
accepted gaps up to ~0.002 under the slack.
Both now find candidates with SpacingOutline and confirm them on
NativeContours, the native contours flattened at a twentieth of the slack
(moved out of PartSpacingReview, which keeps using them). The runner calls
NestLayoutCheck.KeepsSpacing, the same outline, tie rule and
confirmation, so the two validators accept exactly the same pairs.
Clears stays unconfirmed and stricter for engine certification. No
tolerance changed.
FixedStrategyEngine_IrregularJob pins now assert LayoutAssert.Valid with
unchanged digests; the NativeU 70-part grid's 28 reports were the same
cause and its test now requires none.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
BestFitFinder gathered each rotation strategy's candidates, and PairEvaluator
gathered evaluated results, in ConcurrentBags, so their order depended on which
worker finished first. The stable area sort then broke equal-area ties in that
arbitrary order, and fills, which try candidates in order and keep the first of
equal layouts, could nest the same parts differently between runs.
Both now fill index-addressed slots: candidates keep rotation-angle and
slide-offset order, results keep candidate order, and ties break the same way
every run. The candidates produced and their scores are unchanged.
The Strip whole-job pin in FillStackCharacterizationTests is re-pinned
(A66602F707290A36 -> FD03A4529D37E32C). That job ties between best-fit
pairs; the old pin recorded whichever tied pair the bag happened to return
first. The new layout places the same 26 parts, passes LayoutAssert.Valid
and gave the same digest in five separate test processes. The other 28
pins are unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
StripPlateNester sent every request to the strip fills, which try two
classification angles and ignore rotation bounds. With a fixed or bounded
rotation at quantity above one they proposed forbidden poses, the job
validator threw "Candidate rotation is not allowed for the requirement."
and the whole Strip job failed. Strip now uses the same guard as
DefaultPlateNester and hands such plates to OrderedPlateNester.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Characterization digests for the interactive PlateFillService surface and
the fixed-strategy whole-job engines on L-shaped, notched, arc, bar and
chevron parts: single-item fills, whole-plate nests (including one where
learned angles change the layout, guarded by a full-sweep comparison),
fills beside clamp zones, and one job per Fill/Strip/remnant engine.
They let the planned filler/nester consolidation be shown layout-neutral.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Every whole-job engine chooses among the offered stock sizes, and on the
synthetic benchmark nests Default matched or beat StockLadder on all 18
runs (saved sizes, a six-size pool, with and without salvage credit),
costing 30-40% less in total with mixed sizes. Its sheet-swap step never
produced a win over Irregular's tail re-plan.
The registry maps "StockLadder" to Default so saved selections, scripts
and API requests keep working. OrderedPlateNester stays: Fill and the
remnant strategies use it for restricted rotations, and its golden layout
is now pinned through NestJobRunner with the parts requested largest
first, as StockLadder requested them.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Machines, post settings, clamp defaults and nest defaults come from the
nest server once it holds them, and from this PC's files until then; saves
go where the settings were read. The server's copy is re-read when older
than two minutes, before every post and when Machine Configuration opens.
While the server is unreachable the last copy read is used, the user is told
once, and nothing shared can be changed.
Posting re-reads the post's shared settings; saving them is skipped when the
dialog changed nothing, and a conflict loads the other workstation's
settings and stops the post. On first start the desktop offers to upload the
settings the server lacks.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Schema v13 adds shared_settings and shared_setting_revisions behind
/api/settings: one revision-guarded JSON document per kind and key, with
every revision (deletions included) kept with who saved it. Recreating a
deleted document continues its revision count.
OpenNest.Data gains the client (RemoteSharedSettings), a synchronous store
that keeps the last copy read for offline use and refuses writes while the
server is unreachable (SharedSettingsStore), a machine provider over it, and
JSON parse/serialize entry points for clamp settings and nest defaults.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
IJsonConfigPostProcessor lets a host keep a post's settings somewhere other
than the JSON file beside the post DLL. The CL-707, CI Fiber and Gravograph
posts implement it; LoadConfig keeps the current settings when the JSON is
unusable.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Plates now take cut-off settings from the nest's machine, so the
default's 0.25-0.75 clearances replaced the 0.02 operators expect.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Nests with a "planning with cut-offs:" line are planned again after clearing
applied work and adding default scrap cut-offs. OPENNEST_PROBLEM_NESTS_CUTOFFS=1
plans every nest that way to record new lines.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
PEP stores 3/16 as 0.188, which missed the machine's 0.1875 at the
0.0005 in tolerance; widen it to 0.001 in, still far below gauge steps.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The set preview guessed row widths and settled the scale in four rounds,
which could stick at rows of minimum-width label cells and leave much of
a narrow pane empty. At a given scale, filling each tallest-first row as
far as the pane allows is the best row split, and the packed height only
grows with scale, so the layout now bisects for the largest scale that
fits. A 21-drawing set in a 400x590 pane goes from scale 1.14 with 345 px
used to 2.23 filling the height.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The CL-707 config now declares sections, sentence-case labels and ranges,
so its dialog matches the CI Fiber one instead of the generic PropertyGrid.
The sectioned editor gains what the CL-707 config needs: optional (nullable)
numbers behind an enable box, editable tables for lists of simple records,
and a text field that suggests values from a table column (Selected library).
"Lead-in arc line 2 feedrate" is relabeled "Lead-in arc feedrate", which is
what #127 drives.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A record's thickness is in the nest's units, but nothing on the record said
which, so a list of nests could not tell 9.525 mm from 9.525 inches without
reading each archive. Records now carry units, read from the uploaded
archive like the counts (absent or unknown values are inches) and kept by a
metadata-only save. Schema v12 adds the column and reads every stored
archive, current and historical, so existing millimeter nests report it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
An acceptance rule may list sheet grades first, so at plate thickness its
best match can be rank 3 (A36 for HR). Auto Nest marked every row above
rank 1 a substitute; it now ranks rows against the best rule rank ML
matched at the nest's thickness, as ML labels them, so A36 is preferred
and only A572 is a substitute.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
MaterialLedger's Release lets a hold go, so a Released hold no longer keeps
a sheet for the nest; only Proposed, Approved and AwaitingCloseout holds,
the statuses ML counts against free stock, are open. The Has Been Cut
note's link pointed at /Nests/{id}, which ML does not serve; its nest page
is /Nests/Details/{id}.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Each zoom step rebuilt every part's display paths from its CNC program,
and each drag step rebuilt the moved parts, which dominates for parts
with hundreds of holes. LayoutPart now keeps its paths in the drawing's
program frame and only maps them to the view on a zoom or move,
rebuilding when IsDirty is set or the program, rotation or manual
lead-ins change. Also caches the label StringFormat.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
GET /api/nests/{id}/sheets returns sizes as stored, in the nest's units,
but did not say which. MaterialLedger compares them with inches, so a
millimeter nest's sheets never matched inventory. The response now carries
units (inches or millimeters), read the way NestReader reads them: absent
or unknown values are inches.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
MaterialLedger's /api/stock/opennest now resolves an OpenNest material
and grade through ranked acceptance rules. The client reads the new
spec rank, family, grade and finish and the item rank; an older ledger
that sends none of them deserializes as rank 1 with no label.
LedgerStockMapper groups drops only by identical size and spec, keeps
the ledger's order in rows and in each row's ItemCodes, and orders rows
by rank. Auto Nest's Source column shows the row's grade and finish
("A1011 P&O"); substitutes (rank above 1) read "A1011 P&O for HR" in
amber, name the substitution in their tooltip and still load ticked.
The engine still sees no rank.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Server nests in Database mode get a read-only status bar label comparing their
open MaterialLedger holds with the sheets they cut, e.g. "Ledger: 2 of 4 held,
2 short". Nothing writes to the ledger and nothing waits on it.
- MaterialLedgerClient.GetHoldsAsync reads GET /api/stock/holds?openNestNestId=
with the closed LedgerHoldsResult set; unknown status strings are kept. The
request plumbing is shared with GetStockAsync.
- LedgerHoldSummary (OpenNest.Data) counts Proposed/Approved/Released/
AwaitingCloseout holds against the plate quantities, skipping the trailing
empty plate as /sheets does.
- NestHoldStatus refreshes on server open, after save, after storage or
Options changes and on label click; it never polls. The tooltip lists holds
in nest units. File-mode, unsaved and ledger-less nests show nothing.
- Setting Has Been Cut in Nest Info with holds still open shows a non-modal
note linking to {ledgerUrl}/Nests/{id}. Posting is not gated.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Core PlateRemnant.Expected picks a full-span cut-off drop clear of the
parts (less kerf, nominal position for head-locked overcuts), else the
largest salvage edge offcut, else none below the nest's new persisted
MinimumRemnantDimension. NestJobCost's salvage offcut now calls the Core
rule unchanged. NestWriter writes a derived plate expectedRemnant that
readers skip, and /sheets reports it per plate.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Auto Nest on MaterialLedger stock now records which inventory item each
physical sheet uses, so ML can hold exactly those items instead of matching
by size.
- Core: Plate.StockItemCodes (entry i = sheet i of Quantity; empty = uncoded).
Core invalidates it: a resize clears it (turning the sheet keeps it), a lower
Quantity truncates it, a nest material/grade/thickness change clears every
plate's, ClearAll clears it and new plates never copy it.
- Desktop Auto Nest: after a kept proposal is committed, LedgerStockAssignment
deals each ledger row's codes to its plates in Nest.Plates order (bundles
repeat their code; clamp-removal variants use their base row). Rejected,
discarded or cancelled proposals never reach it. NestPipelineCommit.PairWithStock
pairs committed plates with their solved stock; the engine stays ledger-free.
- Plate list tooltip: "Stock: CODE (location)"; locations are display-only.
- nest.json: optional plate stockItemCodes, omitted when empty, read leniently.
- /api/nests/{id}/sheets: new plates[] { index, width, length, quantity,
stockItemCodes }; sheets[] unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Auto Nest's Stock Options gets a Load from ledger button that reads the nest
material's free sheets and drops from MaterialLedger's API-key-protected
GET /api/stock/opennest. Ledger rows are request-local: the engine sees them as
ordinary NestPlateStock rows with ledger:{n} ids and finite quantities, and they
are never written to Nest.PlateOptions.
- OpenNest.Data/MaterialLedger: settings file, read-only client (X-Api-Key,
5 s timeout, closed LedgerStockResult set) and LedgerStockMapper (bundles and
sheets one row each, same-size drops grouped with ordered item codes, unknown
shapes and too-small items skipped, inch/mm conversion).
- Options: MaterialLedger URL and API key (DPAPI, CurrentUser) with Test.
- Auto Nest grid: Use, Qty and Source columns for every row; PlateOption gains
request-local Quantity and Id, which NestStockBuilder passes to the engine.
Ledger rows score by area; hand-typed costs stay saved.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Panning invalidates the view on every mouse move, so a paint is always
pending and WM_TIMER never arrives; the torch froze until the pan ended.
Paints now advance the playhead from the playback clock too.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Converted part programs keep a source CAM's overcut: a hole's arc or a slot's
last line runs about 0.03 past the pierce along the first cut. The rapid check
only counted a contour closed when it ended exactly at its start, so every
overcut contour became an open fragment, the open-cut proof refused them, and
each part reported "Multiple interrupted/open cutting fragments" and an
unverifiable lead-out instead of being checked (P260810-02: all 50 parts).
ReleasedContourState now closes such a contour at its seam (matched at the
1e-6 seam tolerance, since a hole's two arcs carry centers ~1e-7 apart) and
lets the rapid leaving the overcut end ignore contact within that tolerance of
its departure. The nest now validates fully and reports the real crossings it
was hiding: rapids that cross the hole just cut.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A one-pixel fill (about 2% on the Nesting Progress bar) asked GDI+ for a
zero-size corner arc, which threw "Parameter is not valid" mid-nest. Clamp
the corner radius to the rectangle and fall back to a plain rectangle.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Unit suffixes are painted in a reserved right margin instead of being part
of the edit text, so editing the number no longer fails to parse. Length
boxes also convert values typed in other units (mm, cm, m, in, ft,
fractions such as 3/8").
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The set preview moves from its own window into a details pane beside
the list, as the Drawing Library has, with the set's notes below it.
It reads the highlighted set shortly after the selection settles and
caches drawings per revision. Parts are drawn as outlines without fill,
and the info lines sit above the fitted drawings instead of over them.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Drawing data can fix a fillet's center slightly off the tangent normal, so
the arc's end sits ~1e-7 past its neighbouring line's end. The slide contact
classifier only joined entities within 1e-7, so a contact at that tangent
point read as two boundaries, was classified ambiguous and blocked the push.
In N26-243 this stopped a part pushed left along another once the parts
aligned. Contacts within 1e-6 of a joint now take the joint's tangents;
the 1e-7 incidence tolerance is unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Master already starts such entries exactly at the vertex (45592a81), so the
cherry-picked snap was redundant and its test's off-vertex precondition no
longer holds.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
With Nest after release ticked, Make Nests now minimizes the Drawing
Sets window and nests each group's built nest in its own main-window
tab, before it is saved, with Auto Nest's progress window and live plan
strip, one nest at a time in plan order. Stop there (or switching tabs)
stops the whole release, as the panel's Stop does; the layout is kept
by the same rules as the headless renest, without the Keep review.
After upload each tab is bound to its saved record instead of a second
tab opening; a tab whose nest was not saved is closed. The main window
stays in front, and the Drawing Sets window flashes its taskbar button
when a group failed or was refused or the release was not recorded.
NestRenest splits into CreateRequest and Keep so the solve runs off the
UI thread and the commit on it; AutoNestCommand's solve-with-progress
step is shared rather than copied.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The modal release dialog is replaced by ReleasePanel, docked beside the
Library and Sets tabs and shared by both. A double-click or Enter adds a
set at one kit or a library drawing on its own at the entered quantity;
adding one already listed adds to its quantity. Lines are edited in
place with a remove button, and the nests it will make preview live.
Each group now merges into a matching Draft nest by default: the only
one, or the most recently saved of several (chosen in the row); a draft
open in a tab blocks Make Nests instead of making a parallel nest.
Nest after release is remembered per user. Edit Set and Edit Drawing
move to their buttons and right-click menus.
The Drawing Sets window is now an unowned top-level window with its own
taskbar entry and remembered bounds, closed with the main window; a
release not yet made survives closing it, and Make Nests brings the
main window forward. ReleaseSetForm remains as a thin dialog host for
releasing from Nest > Add from Drawing Library.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Full circles now take InternalLeadIn/InternalLeadOut like every other
cutout; the ArcCircle lead settings and the cutting panel's Arc / Circle
tab are removed. Circle-specific geometry handling (radius clamp, angle
rounding, pierce zone) is unchanged.
Older nest files and desktop settings still load: their arcCircleLeadIn/
arcCircleLeadOut keys are ignored and no longer written, so re-planned
circles take the internal leads. Saved part programs are untouched.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A closest-point entry within Tolerance.Epsilon of a line or arc vertex made
ReindexAt start the contour at the vertex while the lead-in still ended at
the off-vertex point, so the cut closed short of its start and replay refused
the whole plate. Snap such entries onto the vertex before emitting the lead-in.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Preview on the Sets tab (button and right-click menu) downloads each
member's current revision and packs them into one view, labeled with
name and quantity, so part sizes compare at a glance. PlateView gains
DrawPartNumbers (default on) so the preview can hide sequence numbers.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Without salvage credit (desktop Auto Nest on a single plate size) every
complete one-sheet layout costs the same, so engines kept whichever layout
came first. N26-23S nested 27.86" long when turning two parts fits it in
21.3".
NestJobCost.CompactnessOffcut measures the largest full-width/full-length
edge offcut as salvage does, whatever the salvage rate. Default and Circles
(CandidateScore), Rectangles and Circles sheet choice (SheetByStock) and
Irregular sheet and plan ranking use it only after cost, so no cost changes.
Sheet-level keys round to 1e-6 to keep ties platform-independent.
Rectangles layout digests are re-captured: each changed fixture keeps its
sheets, parts and cost and leaves a larger offcut.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The benchmark built stock from spacing and quadrant only, so engines were
scored on clamp-free sheets and baselines were never checked against the
clamps they were made with. Stock now comes from NestStockBuilder.FromTemplate,
as in desktop Auto Nest: the source plate's rail is resolved for every
candidate size (explicit zones are offered unchanged), and baseline plates
keep their rail and removed clamps.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Grid columns no longer stretch to fill the control. GridStyle sizes each
column once to its header and the first rows shown (capped at 400 px),
then the widths are the user's to resize.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
File > Drawing Library, Drawing Sets, Releases and database-mode Import
BOM now open the window inside the main form, maximized, instead of as a
modal dialog. A second menu click activates the open window on the tab
asked for. Close now closes the window, since a DialogResult button no
longer does outside a modal dialog.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The drawing library browser becomes DrawingLibraryView, a control. The Drawing
Sets window hosts it as its Library tab beside Sets and Releases, and File >
Drawing Library opens the window on it. A library drawing's Releases item
switches to the Releases tab filtered to it. Nest > Add from Drawing Library
stays a dialog, now a thin wrapper around the same view.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
ColorScheme.Default and LayoutPart kept single static pens, brushes and a
font that every plate view and drawing preview painted with. GDI+ objects
are not thread-safe, so two views painting at once on different UI threads
(parallel WinForms test collections) failed in PlateRenderer.DrawPlate with
"Object is currently in use elsewhere" and crashed the test host.
The scheme now builds its pens and brushes per thread and rebuilds them
after a color change; LayoutPart's selection, lead-in and label objects are
thread-static. A regression test paints previews on four threads at once.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Drawing Sets > More > Import BOM reads a BOM and its drawing folder,
matches each drawing to the library by its D4 identity and geometry
(reuse, new revision, or new drawing) and opens the set editor with a
new set prefilled with the BOM quantities. Reading only queries the
library; Create Set lists the uploads and revisions and asks before
storing them, and the set is stored only by the editor's Save.
Parts with no material or thickness still import and are flagged for
Edit Drawing. DrawingPackage.GeometryKey compares geometry independent
of the fresh entity ids each DXF import assigns. In Database mode File >
Import BOM opens this flow instead of creating nests directly; File mode
is unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The set browser's six equal buttons become New Set..., Edit..., More and a
bold Make Nests.... Archive/Restore, History... and Releases... move into a
menu that the More button drops down and that is also the set list's
right-click menu (menu key and Shift+F10 open it; right-click selects the
row first). Access keys: &New Set, &Edit, M&ore, &Make Nests; the menu has
&Archive/&Restore, &History, Re&leases. Enabled rules are unchanged; More is
enabled while any of its items is. The picker hides More and has no menu.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The member grid shows one Material column (name, grade, thickness and
units, such as "Steel A36 0.25 in"), Qty and Note; Cut type appears only
when the set mixes cut types. Move Up/Down are gone: member order only
breaks ties (materials are grouped and sorted on release, nests list
drawings by name), and the stored order is kept as it was. The dialog
opens at 1040 px instead of 1264, with the library pane unchanged and
still resizable.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The drawing sets window now has two tabs. Releases hosts the release list
(paging, nests, Undo Release, New Release) as a SetReleasesView control that
replaces SetReleasesForm. File > Releases stays as a shortcut that opens the
window on that tab. A set's Releases (Sets tab) and a library drawing's
Releases (Drawing Library) open the tab filtered to it, with the filter shown
above the list and Clear Filter to list every release. Releases re-reads its
page whenever the tab is shown again, so a release made on Sets appears.
The set editor gets History... for a saved set; the Sets tab keeps its
History button until the browser's buttons are rearranged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The release dialog now reads as a sentence ("Release set 'X' ×N") and
previews what Make Nests will do ("Creates 2 nests: ..."), with refused
materials counted and Fix Drawings reachable without selecting them.
An Options toggle holds the Release ticks, the Nest column and Include
archived drawings; collapsed, an option stays shown while it differs
from its default, and the Nest column shows whenever a Draft nest could
be merged into. Defaults, release, undo and retry are unchanged. The
Status column wraps so refusals are not cut off, and the retry status
reads "... Try Again records it; the nests are not made again."
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Wording only, no behavior change: "kit" becomes "set" or "Quantity",
the release button reads Make Nests... (Try Again after a failed
record), the releases list shows Material and Action, and the release
dialog's status lines are shorter. Help in docs/nest-storage.md follows.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Builds on the library's Edit Drawing (details as a new revision):
- warns before saving details that would duplicate another active library
drawing (D4), naming them; a failed lookup also asks;
- File > Drawing Library, a nest-less mode of the library browser that lists
every active drawing and edits on double-click;
- the set editor's member grid (double-click, right-click, button);
- the release dialog: Fix Drawings on a group refused for missing material or
thickness or duplicate names, so those refusals are no longer a dead end.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
ajandClaude Opus 5.5