Tabs suit thin plate, but on anything thicker than 0.25 in the parts
are too hard to break out of the sheet, and the Cutting Parameters
dialog was one global set for every job. Its settings now live on the
nest's machine thickness: leads on the existing Outside/Inside Cuts
tabs, and lead-in angle rounding, tabs and pierce on a new Tabs &
Pierce tab (ThicknessConfig.Cutting). In Database mode every
workstation gets the same settings through the shared machine.
The dialog and the Place Lead-in panel say what they edit, and save
back to that thickness (MachineCuttingDefaults.WriteTo, converted to
the machine's units). A thickness with no Tabs & Pierce of its own, or
a nest the machine has no thickness for, keeps this PC's settings as
before. If the machine can't be saved (server offline, a conflict),
the edit is kept on this PC for that job and the user is told.
Machine Configuration can copy one thickness's Tabs & Pierce to
thinner or thicker ones, so the 0.25 in rule takes a few clicks.
An older desktop saving a shared machine would silently erase these
settings, since it doesn't know them. Machine configuration classes
now keep unknown fields, and the server refuses a machine save that
leaves out a field the stored machine has a value for, telling the
user to update OpenNest.
The Plan Cutting status line now reports tabs from SupportTabs; since
"Tab every part" was retired it always said off.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Nobody tabs every part, but tabbing by size is useful even on a plate
that has a support grid. Cutting Settings > Tabs now offers "Only tab
parts the support grid can't hold level" or "Tab parts by size"
(CuttingParameters.TabBySize), which ignores the bed and tabs each part
whose minimum-area bounding rectangle's narrow side is in the range.
The support grid choice still falls back to that range on plates with
no bed, as before.
The range fields become TabSizeMinWidth/TabSizeMaxWidth; their JSON
keys stay noBedTabMinWidth/noBedTabMaxWidth so saved settings and nests
read unchanged. TabsEnabled stays as the per-contour flag Plan Cutting,
Place Lead-in and drawing pins set on the parts they tab.
Saved user settings with "Tab every part" read as tabs by size from 0
to 9999, which tabs the same parts. Only the user's settings migrate;
a plate's recorded parameters and pins replay as planned.
Plan Cutting, Place Lead-in and the pre-post review all go through
SupportTabSettings, so they agree on which parts need a tab. A
size-tabbed part is held by any clear tab, so it is never a rapid
obstacle.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A support-tabbed part that no single tab can hold level may tip once cut,
yet its tabbed outside was crossable like any retained part, so Plan
Cutting could rapid back across a row of long strips. Its outside is now a
rapid obstacle, closed across its tab gap, in the search, replay, cut-off
insertion and the safest route.
Its fallback entries are ranked toward the next cut rather than steadiest
first, so a long strip can be left toward the next part, and the "cut those
two the other way round" rule applies only when the approach crosses no
other part.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A tabbed outside cut is trimmed short of its entry, but the trim only
handled lines and arcs: a round part's outline is one circle, so it was
cut whole. Plan Cutting counted it as tabbed and called the plan ready,
then the pre-post review found no tab and warned that the part may tip.
Cut a tabbed circle as an arc that stops the tab's chord short of its
entry, travelling the circle's own way.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Small parts on a coarse support grid (the help tutorial's 5 x 5 gussets
on a 2 inch grid) rest on one or two points, so no single tab could
steady them and every plan came back unverified. New cutting settings
now start "Tab alone holds parts up to" at 6; settings saved without the
field still read as 0, so existing settings keep their meaning.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A support-tabbed part that no single tab can hold level was limited to its
one steadiest entry. Two strips stacked in a frame's cutout then blocked
the plate: from the upper strip's only entry, every route to the lower one
crossed holes already cut. Its other entries clear of inside corners now
follow the steadiest, in the search and in contour recovery; the part is
still tabbed and still warned about. Parts a tab can hold keep their
steadying entries.
The unverified headline also named fixed lead-ins when the only warning
was a part that may tip; it now says what needs review.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The repo mixed variants such as center/centre and color/colour, so a
name could be spelled either way and searches missed half the hits.
Standardize on the US spelling, matching .NET's own APIs (Color, Center).
Wire values owned by other systems keep their spelling: the material
ledger's "Cancelled" hold status and GitHub's "cancelled" job status.
No behavior change beyond the spelling of a few status messages.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Add a Support Bed tab beside Clamps that edits the grid or slats new
nests assigned the machine receive. A machine without a bed shows the
legacy support-grid.json values; the first edit stores them on the
machine in its units.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The support overlay was drawn inside the live-plate-only paint block, and
the Plan Cutting preview plate never copied the support bed, so opening
the cut planner hid the grid points and each part's support marks. The
overlay now follows the displayed plate, the preview carries the bed, and
tab-point clearance falls back to the live plate's tab size.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Small parts such as 1.5" test squares on a 2" laser grid rest on at most
one grid point, so no single support tab can bring their center of
gravity inside the contacts and Plan Cutting warned "no single tab can
steady it" on every one. In practice a part that short stays in the
sheet on its tab, so the bed's contacts don't matter.
Cutting Settings > Tabs gets "Tab alone holds parts up to N long"
(CuttingParameters.TabHeldMaxLength, 0 = off, the default). On a plate
with a bed, a part the bed can't hold level whose length (long side of
its minimum-area bounding rectangle) is within the limit is still
tabbed, but any tab clear of inside corners steadies it, so Plan
Cutting, hand-placed lead-ins and the pre-post review warn only when it
has no tab at all. The setting persists with the cutting parameters and
is part of the plan state fingerprint.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
With support tabs on and no support bed, nothing was tabbed and nothing
said so. A new no-bed width range (NoBedTabMinWidth..NoBedTabMaxWidth,
the short side of the part's minimum-area bounding rectangle) now picks
the parts to tab instead. SupportTabSettings.Analyze makes the choice
for Plan Cutting, hand-placed lead-ins and the pre-post review; without
a bed any tab clear of inside corners counts. With no bed and no range,
the plan notes that nothing was tabbed. Cutting Settings > Tabs gains
the range fields, and the values persist with the cutting parameters.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Slats are strips of a set thickness running the full length or width of
the table, one every pitch. A part's contacts are the corners of where its
material crosses a slat, so the support check and support tabs work as on
the grid. Nest > Support Bed... picks grid or slats; nest files store
type "slats" and support-grid.json keeps both layouts' values. Draw
Support shows the slats cut off to the sheet.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The assigned machine now drives the support grid, lead-ins and cut-offs, so
it should be visible without opening a menu. The status bar shows
"Machine: <name>" beside the material; left- or right-clicking it lists the
machines (the same list as Nest > Machine) above the label.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The support grid was one shared support-grid.json, off by default, and a nest
had no machine at all, so a plasma table and a fiber laser could not have
different grids, and nothing could pick machine-specific behavior later
(lead-ins differ between laser and plasma; tabbing depends on the grid).
- Nest.Machine (id + name) persists as top-level `machine` in nest.json;
malformed values load as none.
- MachineConfig.SupportGrid holds each machine's grid; a machine without one
still falls back to the legacy support-grid.json.
- New and BOM import assign the Tools > Nest Defaults machine (first by name
when none is chosen) and give the nest that machine's grid.
- Nest > Machine reassigns a nest and swaps in the new machine's grid;
Nest > Support Grid saves machine defaults to the nest's machine.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Plan Cutting is now the only automatic lead-in assignment, and parts the
support grid cannot hold level are reported wherever they lack a
steadying tab.
- Remove Assign Lead-ins (plate and nest), LeadInAssigner, the lead-in
tool's Auto-Assign button and the Auto Tab size range; old settings
with autoTab sizes still load
- Manual Place Lead-in tabs the clicked entry when support tabs are on
and the grid cannot hold the part (SupportTabSettings)
- New PartSupport finding: Plan Cutting replay and best-effort plans
warn when a drawing pin, a lead-in that does not fit or no single tab
leaves a part unsteady; the pre-post review checks each placed
program's outside tab gap. These warnings replace the advisory
weak-tab notes; only the inside-corner tab note stays advisory, and
never for a pin
- Pinned perimeters keep their pin but carry the support analysis
- Draw grid points as pixel-snapped squares without anti-aliasing
- Post fixtures build lead-ins through a test-only TestLeadIns helper
- Docs: support tabs, pre-post verification and planner notes
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A tab cannot lift a part's margin past its contacts' own hull edges, so a
whole stretch of outline often ties for the best tab point, and the first
sample found won, leaving the tab off-center. Keep the full outline search
for the margin, then among samples within Tolerance.Epsilon of the best,
pick the one nearest the line through the center of gravity across the
long side of the outline's minimum-area bounding rectangle. A part held
only near one end is still tabbed at the far end.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The best tab point used to land in inside corners: equally good points
run along a straight edge, vertices were tried first and the first tie
won. Operators cannot grind a nub flush there.
- SupportAnalyzer finds inside corners (inward-turning vertex runs of at
least 30 degrees, so chorded fillets count) and keeps tab points a
clearance from them; of equally good points it picks the one farthest
from an inside corner. Plan Cutting and the overlay use twice the tab
size; AcceptsTabAt rejects closer points
- When no steadying entry has a lead-in that fits, the search falls back
to entries clear of inside corners, then to every entry, each ordered
by how well the tab steadies the part, keeping only the steadiest that
fit
- Replay notes parts whose planned tab cannot hold them level or sits in
an inside corner; the notes are advisory and leave a Ready plan Ready
- Console/MCP plate summaries print a ready plan's notes
- docs/support-tabs.md and cutting-planner notes
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Model the machine's support bed as a grid of contact points measured
from the plate origin, and check each part's center of gravity against
the convex hull of the grid points under its material. The bed is
extensible so straight and CAD-imported curved slats can follow.
- Core: SupportBed/SupportGrid, SupportMaterial and SupportAnalyzer
(margin with registration tolerance, best single tab point)
- Nest-wide support bed that every plate follows, saved in
plateDefaults.supportBed; machine defaults in support-grid.json
- CuttingParameters.SupportTabs: Plan Cutting tabs only unsupported
parts and limits their perimeter entries to points where the tab
steadies the part, falling back to any fitting entry
- Desktop: Nest > Support Grid..., View > Draw Support overlay and a
"Tab parts the support grid cannot hold level" tab option
- docs/support-tabs.md, nest file format and planner notes
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
ajandClaude Opus 5.5