The repo mixed variants such as center/centre and color/colour, so a
name could be spelled either way and searches missed half the hits.
Standardize on the US spelling, matching .NET's own APIs (Color, Center).
Wire values owned by other systems keep their spelling: the material
ledger's "Cancelled" hold status and GitHub's "cancelled" job status.
No behavior change beyond the spelling of a few status messages.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Trim refused the piece between two crossing cut-offs because a cut-off had
one start and one end, so a line could not be stopped short around a pocket
of parts without deleting it and drawing two. A cut-off now carries Gaps,
stretches between its limits left uncut: segment generation excludes them
like parts, so the line splits into segments that each take their own place
in the cut sequence. Trimming a middle piece adds a gap from one crossing
centre to the other (merged with any it touches), Extend near a gap's edge
closes it, and Swap Through-Cut refuses a junction a gap touches rather
than guess which side of the gap should run through.
Every reader of the limits treats a gap as uncut, so nothing waits for,
warns about or credits a cut that never happens: segment spans stop at a
gap, the cutting dependencies skip a part inside one, the clamp check
ignores a clamp inside one, the cutting-state and overlap stamps go stale
when gaps change, and a gapped line is never full span for the expected
remnant or automatic cut-offs. Gaps persist as an optional gaps array;
older versions ignore it and would cut straight through.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Plan Cutting spent most of its time on work that never changed the outcome:
many-holed parts paid quadratic shape-pair and ring-containment costs before
any search, every plate was captured twice, and failing plates burned their
whole budget in exhaustive fallback passes that never found a plan on 127
production plates.
- OverlapMaterial: skip native shape pairs whose bounds are clear by more
than the query allowance; gate polygon touch and winding tests on vertex
bounds.
- LeadMaterialSnapshot: gate ring enclosure tests on ring extents when
finding the perimeter and rejecting nested cutouts.
- CuttingPlanBatch: capture each plate once; the kept-order retry derives
from the same capture through CuttingPlanSnapshot.WithPreservedOrder.
- JointCuttingPlanSearch: end the kept-order full pass and the sequence-free
recovery and full passes after FallbackStalls (2) stalls' worth of
expansions when programs are regenerated; plates with only fixed programs
keep the exhaustive search so a refusal stays genuine.
On 127 archive plates (lead-ins cleared, 35" scrap cut-offs) total time fell
from 164 s to 102 s with identical outcomes; the problem-nest corpus gives
the same status and expansion count on every plate.
Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
An arc lead-in meeting a straight window edge tangentially has a double
root at its joint. Rounding split it into two contacts a few 1e-8 apart,
or dropped it so the exact ray fallback reported the joint as an
uncertain contact. Either refused a valid entry, so N26-27U's windows
lost most of their entries and the plate never planned.
Treat a contact within 1e-6 of a joint its boundary passes through as
the joint, and let the exact line fallback skip ray hits at contacts
already recorded. The pinned-hole test now expects the other hole's
nearest entry rather than the fallback both runs used to share.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- archived library drawings: say they can't be edited or released; no
front end can restore a library drawing yet
- library filter hint names the Show all materials checkbox
- undo labels Support Bed and Automatic Scrap Cutoffs match their menus
- display-outline posting hints name both Plate > Plan Cutting... and
--plan-cutting, since the console prints them too
- MaterialLedger options are saved per Windows user, not per machine
Small parts such as 1.5" test squares on a 2" laser grid rest on at most
one grid point, so no single support tab can bring their center of
gravity inside the contacts and Plan Cutting warned "no single tab can
steady it" on every one. In practice a part that short stays in the
sheet on its tab, so the bed's contacts don't matter.
Cutting Settings > Tabs gets "Tab alone holds parts up to N long"
(CuttingParameters.TabHeldMaxLength, 0 = off, the default). On a plate
with a bed, a part the bed can't hold level whose length (long side of
its minimum-area bounding rectangle) is within the limit is still
tabbed, but any tab clear of inside corners steadies it, so Plan
Cutting, hand-placed lead-ins and the pre-post review warn only when it
has no tab at all. The setting persists with the cutting parameters and
is part of the plan state fingerprint.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Text cutouts on an ID tag sat a micro-inch below another letter's
baseline. The parity ray, offset a fixed 1e-6 above the test point, ran
exactly through that letter's seam vertex, whose two copies differ in the
last bit, so one edge counted and the tag captured as "Nested cutouts are
not supported material" at some plate locations but not others. The ray
height now steps until no vertex (or arc top/bottom) lies within a small
band of it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
With support tabs on and no support bed, nothing was tabbed and nothing
said so. A new no-bed width range (NoBedTabMinWidth..NoBedTabMaxWidth,
the short side of the part's minimum-area bounding rectangle) now picks
the parts to tab instead. SupportTabSettings.Analyze makes the choice
for Plan Cutting, hand-placed lead-ins and the pre-post review; without
a bed any tab clear of inside corners counts. With no bed and no range,
the plan notes that nothing was tabbed. Cutting Settings > Tabs gains
the range fields, and the values persist with the cutting parameters.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
NestLayoutCheck rejected Fill layouts whose interlocked arcs sat exactly
at the part spacing: its SpacingOutline circumscribes arcs by up to 0.001
each, more than the 0.0005 slack, so facing arcs overlapped. The runner's
placement validator measured inscribed 0.001 polygons instead and so
accepted gaps up to ~0.002 under the slack.
Both now find candidates with SpacingOutline and confirm them on
NativeContours, the native contours flattened at a twentieth of the slack
(moved out of PartSpacingReview, which keeps using them). The runner calls
NestLayoutCheck.KeepsSpacing, the same outline, tie rule and
confirmation, so the two validators accept exactly the same pairs.
Clears stays unconfirmed and stricter for engine certification. No
tolerance changed.
FixedStrategyEngine_IrregularJob pins now assert LayoutAssert.Valid with
unchanged digests; the NativeU 70-part grid's 28 reports were the same
cause and its test now requires none.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Converted part programs keep a source CAM's overcut: a hole's arc or a slot's
last line runs about 0.03 past the pierce along the first cut. The rapid check
only counted a contour closed when it ended exactly at its start, so every
overcut contour became an open fragment, the open-cut proof refused them, and
each part reported "Multiple interrupted/open cutting fragments" and an
unverifiable lead-out instead of being checked (P260810-02: all 50 parts).
ReleasedContourState now closes such a contour at its seam (matched at the
1e-6 seam tolerance, since a hole's two arcs carry centers ~1e-7 apart) and
lets the rapid leaving the overcut end ignore contact within that tolerance of
its departure. The nest now validates fully and reports the real crossings it
was hiding: rapids that cross the hole just cut.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Stock can arrive up to 1.5 in wider than nominal, so only the origin-side
edge is certain. A cut-off with a head-locked overcut cuts past the nominal
far edge with the head height locked, covering the oversize. With that lock,
Plan Cutting may start the far-edge segment at the far edge: overcut outward,
rapid back still locked, unlock, cut toward the origin. Without it the
direction stays fixed, as decided in Project Memory a20ea455.
- CutOff.HeadLockOvercut / FarEdgeFirst, persisted in .nest; HEAD HEIGHT
LOCK/UNLOCK comment markers; far edge is quadrant-aware.
- Planner offers the reversed far-edge segment in the joint search, the
safest route and segment insertion; Apply records the direction.
- Cincinnati CL and CI Fiber posts gain lock/unlock code settings and refuse
head-locked cut-offs while either is empty.
- Automatic cut-off dialog setting (off by default, 1.5 in), kept between
sessions and used for new cut-offs.
Lock codes and machine behaviour with the head locked are unconfirmed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A part with about 1,700 holes (P241017-01) never planned: material
capture paired every boundary with every other one and lead checks
scanned every boundary per lead, so both hit the 1M native query limit
and the plate fell back to an unverified best-effort plan.
- Material capture sweeps boundary extents along X and queries only
pairs the lead checks' per-pair clearance cannot skip, in the full
scan's order.
- Material with 64+ boundaries keeps a grid of boundary extents. Lead
checks, contour-joint matching and replay's contour accounting query
only nearby boundaries; ray parity reads only holes on the point's row.
- Only native queries that run are charged to the budget; skipped far
material no longer costs its full boundary count.
- The search looks up chosen holes and route ranks instead of scanning.
With that the plate plans Ready, but in 189 s: every step re-emitted
and re-checked all holes already cut. On parts with 64+ contours a
middle hole step now checks only the contour it adds, continuing the
completed-contour state its prefix left (ReleasedContourState.Continue).
It falls back to the full prefix whenever it cannot continue exactly,
and the last contour still checks the whole part from before it.
Isolated contour emission clones only the chosen contour.
P241017-01 now plans Ready in 5.4 s with an identical route, expansions
and rapid travel. Core and engine suites pass; the problem-nest corpus
matches the unchanged commit's outcomes and expansions.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The posts treat every non-lead feed move as a cut, so an applied blank's
display tail, or the outline of a blank posted without a plan, would have
been cut along the blank's edge. The pre-post review counted that outline
as an ordinary cutting contour.
Cincinnati, CI Fiber and the engraver now read part programs through
DisplayPerimeterTail.ForPosting: an applied program posts exactly what the
same program posts with its tail removed by hand, and an unplanned display
perimeter is refused with a message that names the part and points to Plan
Cutting. The pre-post review reports the unplanned outline by name.
Plan Cutting is now the only automatic lead-in assignment, and parts the
support grid cannot hold level are reported wherever they lack a
steadying tab.
- Remove Assign Lead-ins (plate and nest), LeadInAssigner, the lead-in
tool's Auto-Assign button and the Auto Tab size range; old settings
with autoTab sizes still load
- Manual Place Lead-in tabs the clicked entry when support tabs are on
and the grid cannot hold the part (SupportTabSettings)
- New PartSupport finding: Plan Cutting replay and best-effort plans
warn when a drawing pin, a lead-in that does not fit or no single tab
leaves a part unsteady; the pre-post review checks each placed
program's outside tab gap. These warnings replace the advisory
weak-tab notes; only the inside-corner tab note stays advisory, and
never for a pin
- Pinned perimeters keep their pin but carry the support analysis
- Draw grid points as pixel-snapped squares without anti-aliasing
- Post fixtures build lead-ins through a test-only TestLeadIns helper
- Docs: support tabs, pre-post verification and planner notes
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A lead check scanned every other part's material with native contact
queries. On the 5,742-washer plate that was about 80% of planning and
it never finished inside 120 s.
The earlier extent filter (reverted in ea1270e1) used a fixed 0.001 gap,
which native line/circle rounding can exceed for long leads beside small
circles. This skip adds 1e-6 times the span of both extents. The
discriminant's rounding is bounded by about 1e-7 times that span, and
about 2e-9 is seen. So a skipped material has no native contact, and the
900000-long lead beside a small circle is still checked. Each skipped
scan is charged to the native query budget as if it ran. Ray parity is
still asked natively unless the lead's midpoint is outside the
material's Y range. The pierce zone skips only material farther than its
radius by the same gap.
A randomized test checks that skipped material never has a native
contact. It fails with the span allowance at zero and passes with it as
low as 1e-8. Plate 1 of the washer nest now plans Ready in about 54 s.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Validate Nest, the posting review and console --post now report a
"Part spacing" finding for pairs of parts that do not overlap but sit
closer than the plate's part spacing. Before, only Auto Nest's
Keep/Discard review checked spacing, so hand-edited layouts could be
validated and posted with parts too close together.
Candidates are found with Auto Nest's own outline test, moved into Core
as SpacingOutline (NestLayoutCheck and NestTolerances now use it; Engine
tests unchanged). Because that outline circumscribes arcs by more than
the spacing slack, each candidate is confirmed on native contours
flattened 20x finer than the slack, so arcs placed exactly at the
spacing by interactive fills stay clear. The finding reports the
measured gap and marks the middle of the closest approach. Overlapping
pairs, cut-offs, zero spacing, the plate edge and clamps are not
reported as spacing findings.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Thick plate pierces leave a crater wider than the kerf. CuttingParameters.PierceDiameter
(Cutting Settings > Pierce Diameter, 0 = off) requires every lead-in pierce to keep half
of it from all part material: its own contour, its holes and every other part.
- LeadPathValidator checks the zone during Plan Cutting candidate checks and final
replay; fixed emissions warn as usual. No-fit findings explain the zone.
- PierceZoneReview reports Pierce zone warnings before posting for leads from any source.
- Holes whose configured pierce is inside the zone move it toward the hole's PolyLabel
pole (round holes: the centre), as close to the contour as the zone allows; a hole
too small for the zone is pierced at its pole and the shortfall is still reported.
- Straight corner leads and round-hole clamping use the larger of PierceClearance and
the zone radius. The manual lead-in preview shares the Core rules.
- Persisted through the DTO, owned copies and state fingerprint.
Perimeter fallback is not included; see docs/geometry/pierce-zone.md.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A converted outline whose seam closes within the admitted 1e-6 gap could
only be entered at its seam: entered anywhere else, the arc after the
seam started off its own circle and every emission was refused as an
inconsistent radius. The search then spent its whole budget on that
part and the plate never planned. Emission now bridges the gap with a
straight move and cuts the arc as drawn; the verifier already admits
that slack. An entry on the seam vertex is left as before.
Each prefix of a part re-checked its earlier contours' leads against
every other part's material. One search now remembers each verdict by
the lead curve's exact bits and the material's reference, charging the
same native query budget; replay never uses it. On the reported plate
the memo alone gives a byte-identical result in 57 s instead of 12 min 47 s;
with the seam fix the plate plans Ready in about 17 s.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A cutout cut in several pieces around tabs, as PEP programs often are, made
pre-post review report every piece's lead-out and the part's open fragments
as incomplete. Review now proves such open cuts release nothing: within the
part they touch other cuts only at their own ends and form no loop (each
closed contour with its leads counting as one point), and leads at open ends
stay out of the gap beyond them. Anything else stays incomplete. Plan Cutting
keeps refusing to certify its own tabs followed by a lead-out.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Posting review now proves containment exactly as the cutting planner does
(shared NestedPartContainment) and warns when a nested part is cut after its
host (NestedCutOrder) or when a host's hole lead or the nested part's lead
meets the other's material (NestedLead), including subprogram hole poses.
Ambiguous containment is incomplete, never clear; fixed-lead motions are not
reported twice. A committed cutout preview warns until Plan Cutting cuts the
insert first.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Assign Lead-ins (LeadInAssigner) now leaves every unlocked part with active
drawing pins unchanged and returns those parts, so it never overwrites a pin
with the plate's settings; the desktop names them ("N parts kept their
drawing lead-ins (plate P: parts ...); use Plan Cutting to apply their
drawing pins."). Parts without pins, with pins switched off, or locked are
assigned or skipped exactly as before.
The pre-post review now covers drawing pins. A part with active pins whose
placed program does not cut each pinned contour exactly as the pin's own
emission (re-emitted with the part's cutting settings and matched motion for
motion) warns "Drawing pins not applied", as do locked lead-ins overriding
pins and a pin that no longer matches the geometry; pins switched off are
not reported. The contours that are cut as pinned join locked programs in
the fixed-lead re-check against every part's clean material, and fixed
leads are now also checked against active clamps (Plan Cutting itself does
not model clamps).
AGENTS.md records the fixed-emission safeguard and the characterization
digests.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
D1a (user, 2026-10-14): one locked cutout must not refuse the whole layout.
With confirmed parameters a locked program is now a fixed emission, accepted
as given. The replay checker and the lead validator take a per-motion owner:
a violation inside the fixed emission (a lead meeting another part's or its
own material, a rapid inside the locked program crossing a cut contour, an
uncertifiable tab gap or a partial/reversed/retraced cut) is recorded apart
instead of failing the candidate. The search never rejects or learns an order
rule from them, so fixed emissions never steer it; the planner's rapid into
the locked program and every regenerated lead keep every strict check.
Replay turns those violations into typed FixedLead findings that name the
part, contour and the part hit. A plate whose only findings are these is
BestEffort with IndependentlyReplayed set: never Ready, applicable only with
the per-proposal acceptance, and CuttingPlanService.Apply still rejects it.
Overlap, unreadable programs, stale input and cancellation still block, and
unlocked programs a caller left ineligible and the no-parameter route keep
refusing as before.
Pre-post review now re-checks locked leads against every part's clean
material, so the same violations reappear before posting.
Existing tests that encoded the old locked refusal now assert the warning;
two batch tests that used a locked crossing as their hard block use an
overlap instead. The 5.1 digests are unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The spec review found two places where the marker and threshold
contract does not hold.
A clamp narrower than the chord tolerance is still judged
tolerance-free against finely re-read material and reported as the
whole clamp rectangle. That existing safety policy is kept, so its
marker is the clamp's centre: within half the clamp's size (under
0.0005) of the material, though not necessarily on it. Document this
on PlateOverlapPair.Marker and in the overlap docs, and lock it in the
tiny-clamp region test.
Also document that 1e-8 grid rounding can move an area within
rounding error of the 1e-5 threshold to either side of it.
The overlap crosshair sat on the pair's area centroid. For a split,
holed or concave overlap, that point can be off the red material:
between two patches, in a hole, or inside a curve.
PlateOverlapPair.Marker is a point inside the pair's largest island.
It is the island's pole of inaccessibility (PolyLabel), searched to a
tenth of the island's area/perimeter within a 4096-cell budget. If
that bounded search does not land inside (a long thin sliver), the
marker falls back to the midpoint of the widest interior run of a
horizontal scan line placed between vertex heights.
The overlay crosshair, marker hit testing, hover coordinates
("Marker:") and the cutting-inspection ring now use the marker.
Centroid stays the true area centroid. View > Overlap Check > Display
> Centroids is now labelled Markers.
Before the marker existed, its call sites used the centroid. Two
patches, a covered frame, a half annulus and a thin crescent then put
it off the material; now all four land on it. Disabling the scan-line
fallback fails its test. On the 389-plate corpus, markers add about
0.4 ms per overlapping pair; pair and area results are unchanged.
The material-overlap diagnostic clipped every triangle of one part
against every triangle of the other, then carved each fragment by
every hole triangle. Curved overlaps produced thousands of fragments,
and a part sitting inside another part's cutout was slow even when
clear.
PlateOverlapAnalyzer now intersects each candidate pair's hole-aware
material once with Clipper2, in part-local coordinates on a 1e-8 grid.
Each operand is its outline minus the union of its holes (positive
fill rule). Regions become connected islands: a counterclockwise
outline plus clockwise Holes, including an island that both parts'
holes enclose together. PolygonAreaMoments.TrySubtract gives each
island's net moments. A pair is reported when its total shared area
exceeds Tolerance.Epsilon. Out-of-range or nonfinite coordinates make
the pair incomplete rather than clear. The overlay and the cutting
inspection highlight fill outlines with their holes.
On 389 real PEP-converted plates the pair, clamp-finding and issue
sets are identical to the previous kernel. Pair areas are equal or up
to 0.0002 larger: the kernel drops fragments below its area threshold.
With material prepared, the per-plate clipping maximum fell from
2.6 s to 52 ms (total 5.0 s to 0.5 s).
Engine and validation checks still use Collision.
PlateOverlapRegion vertices repeat their closing vertex, and the
desktop overlay drops that last vertex when it builds the fill path.
The tolerance-free tiny-clamp finding returned four open corners, so
the overlay drew it as a triangle. Close the ring like every other
region.
Check Overlaps dismissed a tiny clamp by the part's coarse material bounds
before the fine tolerance-free test ran, but that material is inscribed at
the 0.001 chord tolerance: real material in the sliver beyond a convex arc
(a short arc cap, a rotated crescent) lay outside those bounds and the clamp
read as clear. For clamps below the tolerance the bounds are widened by the
chord tolerance before rejecting.
PM 407f5eb7-329f-41e4-947e-64ad52aa4034 (review s6-delta3-review.md)
Circumscribing every arc holds all material along convex arcs but drops a
sliver along concave ones (a notch), so a tiny clamp 6e-7 into the material
beside a notch read as clear. Tiny-clamp checks now test the part flattened
both ways (all arcs inscribed, all arcs circumscribed): along any arc one of
the two holds the real material, so together they find every real overlap.
PM 407f5eb7-329f-41e4-947e-64ad52aa4034 (delta review s6-delta2-review.md)
Fine inscribed flattening still let a native arc cut 6.2e-7 into a 1e-5
clamp unseen: less than one chord's sag, so the layout check, interactive
fill and Check Overlaps all called it clear. Tiny-clamp checks now
circumscribe perimeter arcs and inscribe cutout arcs (lines stay exact), so
the polygons hold every bit of real material. Any real overlap is reported;
the cost is a possible report within the tolerance of an arc, never a false
clear. The analyzer builds the same polygons instead of a second
OverlapMaterial read.
PM 407f5eb7-329f-41e4-947e-64ad52aa4034 (delta review s6-delta-review.md)
The tolerance-free rectangle test was fed approximated material: the layout
check passed it the 1e-4-grid validation outline (a strip of real material
that wholly contains a 1e-5 clamp could vanish), and interactive fill and
the overlap check passed 0.001 inscribed arc chords (a clamp inside a disk
but outside its chords read as clear). All three now flatten the native
contours at a quarter of the clamp's smaller side, lines kept exact, so the
arc-chord sliver can never hold the clamp. Ordinary clamps are unchanged.
PM 407f5eb7-329f-41e4-947e-64ad52aa4034
Collision.Check finds no overlap region for a clamp smaller than its
tolerance, so Check Overlaps reported a part covering a 1e-5 clamp as clear.
Clamps below 0.001 are judged with KeepOutOverlap and reported as a finding
whose fragment is the whole clamp rectangle; flush and clear parts stay clear.
PM aa995123-295f-479c-adc4-b0cbcb7cf838
The desktop captures the overlap freshness stamp before its error
boundary, and a null cut-off or clamp zone in the plate's lists threw
NullReferenceException there. Stamp missing entries as a distinct empty
state so the whole-plate capture can report the malformed input as a
failed check instead.
Project Memory: opennest cdbe2629-b562-46ee-9509-2b120a511654
Pre-post clamp checks looked only at nominal cut-off definitions and
rapids. A definition moved without regenerating its placed program
left a cut through an active clamp that posted with no warning, because
cut-off material is excluded from the overlap check.
Also check each cut-off part's placed cutting motions against the
clamps in the placement frame (lines exactly, arcs by their extent).
Report one warning per cut-off part and clamp, so a current definition
does not produce a duplicate of its nominal finding.
Project Memory: opennest cdbe2629-b562-46ee-9509-2b120a511654
Plate.ClampZones are stored relative to the sheet's lower-left corner,
but cut-off positions, motions and part poses use the signed quadrant
frame. The automatic cutoff planner, manual cut-off contacts, clamp
rapid warnings and whole-plate overlap capture compared the two
directly, so in quadrants 2-4 a cut or rapid through a real rail clamp
was neither avoided nor warned about.
Add ClampZoneFrame.ToPlacement, which maps live zones into the
placement frame exactly like the sheet and engine stock, and use it in
every Slice 5 consumer. It rejects missing or malformed zones (bounds
stay publicly mutable); pre-post verification reports those as an
incomplete clamp check instead of a clear result. Overlap freshness now
treats a size or quadrant change as moving the zones.
Tests use real ClampRail zones in all quadrants; the hand-signed
quadrant fixtures that hid the defect are converted to rails.
Project Memory: opennest 274836d5-fb76-4619-b3cc-0c811e767dd6
Nests converted from another CAM system carry its seam overcut inside the
clean contour: the last cut runs on past the contour's own start along its
first cut, then a straight jog returns to the start. The ring then touches
itself at its seam, so neither the cutting planner nor the overlap analyzer
could certify it and the whole plate refused.
SeamOvercut recognizes exactly that shape (same line, or same circle and
direction) and trims it from an owned copy; the retraced tail encloses no
area, so material is unchanged and the drawing is never edited. Any other
self-contact still refuses. Arcs of one circle whose centers were each derived
from their own endpoints agree only within Epsilon, so their spans are now
compared at the seam tolerance: shared spans still refuse as overlap, while
arcs that only meet at a joint or lie apart no longer do.
Plates with parts nested in other parts' cutouts then failed to route, since
the host is cut last and every straight approach from the middle of a crowded
cutout crosses a finished neighbour. CuttingNestedOrder tours each host's
inner parts as one run ending beside the host's own contours, hosts follow
the parts beside them, and learned rules still win. Outside entries are
ordered by clear sight lines to the next cut, the look-ahead toward a host is
its nearest contour point rather than its centre, a cutout containing the
arrival point is routed from that point, and a pass that teaches an order
rule ends the round instead of repeating the blocked approach.
Tests: SeamOvercutTests and CuttingNestedOrderTests; the cutting-planning,
diagnostics and overlap tests in OpenNest.Tests pass (1023 passed, 6 skipped).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Report, dialog and diagnostic text across post verification, cutoff
planning, alignment and cutting-plan review repeatedly told the user
what checks weren't (safety certifications, proof, guarantees) instead
of what to do. Reworded these to state the same caveats affirmatively
(inspect X, confirm Y, review Z) without changing the underlying
safety guidance, and updated the tests/docs that pinned the old wording.
Point-in-material used exact Y comparisons, but rings are only nominally
closed: capture admits closure seams and PEP-converted or rotated geometry
carries sub-micro-inch vertex jogs. When a jog straddled the test ray's Y,
the two edges at that shared vertex disagreed which side it was on and the
parity flipped, so a point ten inches outside a material read as interior.
LeadMaterialSnapshot reported leads as entering a neighbour they could not
touch, and the enclosing-perimeter check refused to capture materials whose
rings it misclassified.
Snap the ray comparison by the admitted seam tolerance so both edges at a
shared vertex decide together. Features larger than the tolerance still
count, and containment of a point within the tolerance of an edge stays as
ambiguous as before. On the 93-plate corpus 83 plates are untouched, one
previously refused plate now plans and replays, and 48/93 plates reach
Ready. Accepting more leads also changed one plate's first-found route to a
longer rapid path; that is search ranking, recorded with the measurements.
Also drops an extent-prefilter fast path measured at -6.8% corpus time: it
cleared leads whose native contact was reported beyond any fixed bbox
margin, which NearbyMaterialCheckTests deliberately pins as a refusal.
Capture and preparation agree that a nominal contour may close within
NominalContourClosure.Tolerance inclusively, which converted drawings rely on:
the sampled production corpus carries vertex gaps up to 1e-6. Replay
verification still compared those rings at the exact geometry epsilon, so the
one joint a rotated tool path legitimately bridges refused the whole plate
after the search had already spent its budget.
Census of 91 plates from 60 stored nests: every searched plate containing such
a seam refused with contour-accounting (4 plates, 76.5s of wasted search, worst
71.7s for one 11-part plate), and none of the 42 ready plates had one. Replay
now carries that same admitted endpoint gap as positional and length slack for
the affected ring only. Direction sign, coverage order, retrace detection, ring
counting and selected-emission binding keep the exact epsilon, and capture's
closure admission is unchanged.
With the fix the census yields 45 ready plates instead of 42, no plate changed
any other way, and expansion counts are identical wherever status matched.
P260805-01's 16-part plate plans in 0.76s rather than refusing after 4,129
expansions.
Tests: SeamClosureReplayTests covers seams of 0, 5e-7 and 1e-6 plus four
accounting faults (missing edge, reversed edge, interior shift beyond the
admitted seam, second circuit) that must still refuse, and the beyond-tolerance
capture refusal. OpenNest.Tests 3751, OpenNest.Engine.Tests 690 and
OpenNest.IO.Tests 79 pass; Windows-only projects cannot build on Linux.
Plan Cutting refused ordinary filleted parts with "Native contact query is
numerically uncertain." Material capture checks every curve pair of a ring,
adjacent ones included. Where a line meets a tangent arc at their shared
vertex, rounding can drop the tangent root of the native line/circle
quadratic; the exact ray cast from the line's far end then reached the
vertex, which is already recorded as an endpoint contact, and was read as a
contact the native query missed. Rounded rectangles rotated off-axis were
refused 1037 times in 1080 before this change and 0 times after.
The exactness rays now stop short of a line endpoint the other curve already
contains (half-way from each end when both are contained), so together they
still cover every other point of the line and any unrecorded contact still
refuses. The native kernel and tolerances are unchanged.
Regressions: four tangent-fillet rings and a rotated filleted part planned
through CuttingPlanBatch (red before, green after); a line ending inside a
small circle's contact band stays uncertain in both directions. Mutations that
treat either endpoint as always contained, drop the start ray, or count
recorded endpoints as native contacts all fail.
Project Memory: 41880037
The delta review found two more ways the extent filter could skip a
check a native query would have flagged:
- Native line intersections accept points 0.00001 outside each line's
bounding box, so a lead 0.000003 from another part touched it while
their extents were 0.000003 apart, beyond the 1e-6 margin.
- Around a circle of radius 5e11, rounding let the native query count
a rapid at x = -0.00001 as touching although the circle's extent
started at x = 0; the margin scaled only with the rapid's own size.
Rather than chase each tolerance, the filter now has one narrow rule:
Extent.IsClearOf skips only when both extents are finite, lie within
1e6 and are more than 0.001 apart on some axis. 0.001 is ten times the
widest absolute band of any native contact query (the 0.00001 box
allowance and the 0.0001 contact reach of tiny arcs), and within 1e6
rounding stays far below it. Larger geometry is always checked in
full, as before the filter. Planning speed is unchanged (144-part grid
about 0.5-0.8 s).
All three reproductions are regression tests, with a test of the rule
itself.
IsSeparatedFrom promised that NaN bounds are never separated, but a
finite axis could still compare as separated when the other axis held
NaN. Program reading already refuses nonfinite coordinates, so no
public path was affected; the helper now checks every bound and the
margin are finite before comparing, which also covers the empty
extent of an incomplete material snapshot.
Review of the extent filter (bfe2e51) found it could skip checks the
native queries would have flagged. ContactAfterStart counts a point as
touching an arc while its squared distance from the centre is within
1e-8 x max(1, 2r) of r^2, which for small arcs reaches well past the
radius (up to 1e-4 as r -> 0), more than the filter's margin. A rapid
0.000002 outside a radius-0.001 circle lost its crossing, the pre-post
review lost the same finding, and a lead grazing a radius-0.003 circle
turned from an uncertain check into a clear one.
An arc's extent now uses that contact reach, computed from the same
slack expression as ContactAfterStart, so every point a native query
can count as contact lies inside it. The three cases above are
regression tests.
Every lead was checked against every placed part's material and every
rapid against every completed contour, so each check cost O(parts) and
planning a plate cost O(parts^2). Lead checks were 88% of planning time
on a 144-part grid.
LeadMaterialSnapshot and each completed contour now keep a conservative
extent (an arc counts as its whole supporting circle). A lead or rapid
skips material or a contour only when the extents are farther apart
than 1e-6 x (1 + coordinate size), far above the contact tolerance, so
results are unchanged: anything touching or closer still gets the full
native check. The rapid filter also applies to pre-post verification,
which shares ReleasedContourState.
New tests cover the cases just inside the skip: an arc lead and a
completed arc whose bulge reaches past their endpoints, and a lead and
a rapid that only touch another part's extent.
1b422ef read absolute-mode hole subprograms by converting an
incremental-mode copy of every clean program. Rebuilding absolute
endpoints from incremental deltas is not exact: after a rapid at
1e12 a 1x10 rectangle moved by about 2.4e-5 and a real 2e-5 overlap
was reported clear, in the overlap overlay and pre-post verification
as well as Plan Cutting.
Convert programs directly again, which reads absolute coordinates
exactly, and refuse an absolute-mode subprogram as an incomplete
check instead: the converter adds a call's frame offset to
incremental moves only, so it would read such a hole at its frame
origin. OpenNest writes hole subprograms in incremental mode. The
null-list and unknown-instruction refusals from 1b422ef stay, and
CopyForGeometry is private to the planner again.
ajandClaude Opus 5.5