5776fa80 dropped a tabbed outside's lead-out when it would reach the lead-in,
which silently changed the user's cutting settings. The emitter now keeps the
lead-out as configured again. Plan Cutting plans strictly first, as before;
only when that is refused because such a lead-out may cut its tab free does it
plan again keeping the lead-outs. Each affected part gets a "Tab lead-out"
issue (new PostVerificationKind.TabLeadOut), is treated as cut free for later
rapids, and the plan is UNVERIFIED, so applying it needs explicit acceptance.
The short reorder pass never settles for such a plan, so a clean route still
wins. Locked, fixed and posted programs keep the incomplete-check finding.
The "no single tab can steady it" support warnings caused more trouble than
they solved, so a tabbed part now counts as steady wherever its tab is: Plan
Cutting and the pre-post review warn only about a part cut with no tab at
all, and a tabbed part stays crossable once cut instead of being avoided as
one that may tip. Entry choice still prefers the steadiest tab point.
The problem-nest corpus is unchanged except N26-2AM, whose baseline is now
BestEffort with 15 tab lead-out warnings.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Nobody tabs every part, but tabbing by size is useful even on a plate
that has a support grid. Cutting Settings > Tabs now offers "Only tab
parts the support grid can't hold level" or "Tab parts by size"
(CuttingParameters.TabBySize), which ignores the bed and tabs each part
whose minimum-area bounding rectangle's narrow side is in the range.
The support grid choice still falls back to that range on plates with
no bed, as before.
The range fields become TabSizeMinWidth/TabSizeMaxWidth; their JSON
keys stay noBedTabMinWidth/noBedTabMaxWidth so saved settings and nests
read unchanged. TabsEnabled stays as the per-contour flag Plan Cutting,
Place Lead-in and drawing pins set on the parts they tab.
Saved user settings with "Tab every part" read as tabs by size from 0
to 9999, which tabs the same parts. Only the user's settings migrate;
a plate's recorded parameters and pins replay as planned.
Plan Cutting, Place Lead-in and the pre-post review all go through
SupportTabSettings, so they agree on which parts need a tab. A
size-tabbed part is held by any clear tab, so it is never a rapid
obstacle.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Small parts such as 1.5" test squares on a 2" laser grid rest on at most
one grid point, so no single support tab can bring their center of
gravity inside the contacts and Plan Cutting warned "no single tab can
steady it" on every one. In practice a part that short stays in the
sheet on its tab, so the bed's contacts don't matter.
Cutting Settings > Tabs gets "Tab alone holds parts up to N long"
(CuttingParameters.TabHeldMaxLength, 0 = off, the default). On a plate
with a bed, a part the bed can't hold level whose length (long side of
its minimum-area bounding rectangle) is within the limit is still
tabbed, but any tab clear of inside corners steadies it, so Plan
Cutting, hand-placed lead-ins and the pre-post review warn only when it
has no tab at all. The setting persists with the cutting parameters and
is part of the plan state fingerprint.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
With support tabs on and no support bed, nothing was tabbed and nothing
said so. A new no-bed width range (NoBedTabMinWidth..NoBedTabMaxWidth,
the short side of the part's minimum-area bounding rectangle) now picks
the parts to tab instead. SupportTabSettings.Analyze makes the choice
for Plan Cutting, hand-placed lead-ins and the pre-post review; without
a bed any tab clear of inside corners counts. With no bed and no range,
the plan notes that nothing was tabbed. Cutting Settings > Tabs gains
the range fields, and the values persist with the cutting parameters.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Plan Cutting is now the only automatic lead-in assignment, and parts the
support grid cannot hold level are reported wherever they lack a
steadying tab.
- Remove Assign Lead-ins (plate and nest), LeadInAssigner, the lead-in
tool's Auto-Assign button and the Auto Tab size range; old settings
with autoTab sizes still load
- Manual Place Lead-in tabs the clicked entry when support tabs are on
and the grid cannot hold the part (SupportTabSettings)
- New PartSupport finding: Plan Cutting replay and best-effort plans
warn when a drawing pin, a lead-in that does not fit or no single tab
leaves a part unsteady; the pre-post review checks each placed
program's outside tab gap. These warnings replace the advisory
weak-tab notes; only the inside-corner tab note stays advisory, and
never for a pin
- Pinned perimeters keep their pin but carry the support analysis
- Draw grid points as pixel-snapped squares without anti-aliasing
- Post fixtures build lead-ins through a test-only TestLeadIns helper
- Docs: support tabs, pre-post verification and planner notes
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>