Repo-wide sweep with the pinned CSharpier 1.3.0 tool. Whitespace and
line-wrapping only; OpenNest.Engine.Tests (109) and OpenNest.IO.Tests
pass after reformat, full solution builds 0 errors.
Added .csharpierignore so csproj/config XML keeps its existing layout
(CSharpier's XML wrapping churns attributes with zero benefit).
Formatting is now enforceable: dotnet csharpier check . passes.
Add OpenNest.IO/Bending/BendRepair: opt-in repair of unambiguous paired
ETCH/SCRIBE bend ticks, bounded to <=3.175 mm endpoint movement with
explicit source units. Cut geometry is never modified.
- CadImportOptions.BendRepair configures it; CadImportResult exposes
per-bend BendRepairReports; CadImporter/Dxf wire it into import.
- Console: --repair-bends-mm <limit> --cad-units inches|mm prints
per-bend reports for newly imported DXFs.
- New OpenNest.IO.Tests project (net8.0, synthetic DXFs, 30 tests)
covering bend detection and repair, added to the solution.
- Update README.md and CLAUDE.md for the new pipeline and build/test
instructions.
SolidWorks drawings sometimes place centerline bend markers on the
default layer instead of a dedicated BEND layer.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Geometry Simplifier:
- Replace least-squares circle fitting with mirror axis algorithm
that constrains center to perpendicular bisector of chord, guaranteeing
zero-gap endpoint connectivity by construction
- Golden section search optimizes center position along the axis
- Increase default tolerance from 0.005 to 0.5 for practical CNC use
- Support existing arcs in simplification runs (sample arc points to
find larger replacement arcs spanning lines + arcs together)
- Add tolerance zone visualization (offset original geometry ±tolerance)
- Show original geometry overlay with orange dashed lines in preview
- Add "Original" checkbox to CadConverter for comparing old vs new
- Store OriginalEntities on FileListItem to prevent tolerance creep
when re-running simplifier with different settings
Bend Detection:
- Propagate bend notes to collinear bend lines split by cutouts
using infinite-line perpendicular distance check
- Add bend note text rendering in EntityView at bend line midpoints
DXF Import:
- Fix trimmed ellipse closing chord: only close when sweep ≈ 2π,
preventing phantom lines through slot cutouts
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
DrawingSplitter now clips bend lines to each piece's region using
Liang-Barsky line clipping and offsets them to the new origin. Bend
properties (direction, angle, radius, note text) are preserved through
the entire split pipeline instead of being lost during re-import.
CadConverterForm applies the same origin offset to bends before passing
them to the splitter, and creates FileListItems directly from split
results to avoid re-detection overwriting the bend metadata.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
ConvertProgram.ToGeometry() created entities without setting Color,
defaulting to Color.Empty (alpha=0). After ededc7b switched from
Pens.White to per-entity colors, these rendered fully transparent.
- Add explicit colors to all SpecialLayers (Cut=White, Rapid=Gray, etc.)
- Set entity Color from layer in ConvertProgram for lines, arcs, circles
- Add GetEntityPen fallback: treat Empty/alpha-0 as White
- Add bend line rendering and selection in EntityView/CadConverterForm
- Fix SolidWorksBendDetector MText formatting strip for bend notes
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Introduces a pluggable bend detection system in OpenNest.IO.Bending:
- IBendDetector takes CadDocument directly to preserve MText/layer/linetype info
- SolidWorksBendDetector finds lines on BEND layer with CENTER linetype and matches nearby MText notes
- BendDetectorRegistry auto-registers SolidWorks detector and supports AutoDetect
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
aj
