Commit Graph
11 Commits
Author SHA1 Message Date
ajandClaude Fable 5.2 163a9c83d9 test(best-fit): pin crescent pair spacing on material-only outlines
The crescent reported as a slide defect (pairs inside the part spacing)
was a measurement artifact: the probe counted the program's opening
rapid as outline, a 0.2 spur outside the disc on the converted part.
Measured on material alone every candidate keeps the spacing, so the
slide solver is unchanged. Adds the rounded, origin-outside crescent
with its hooked first contact and documents the oracle rule.

Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
2026-11-15 14:25:44 -05:00
ajandClaude Fable 5.2 07f30c1236 fix(engine): settle best-fit pairs sideways so they close to the part spacing
The pair search slid part 2 in from offsets on a 0.25 step grid, so a pair
that locks in a corner (two interlocking channels) stopped up to a step short
of the tightest fit. Each resting position is now also slid sideways, both
ways, and the new resting positions join the candidates.

Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
2026-11-13 18:25:25 -05:00
ajandClaude Fable 5.2 9b7082e92f fix(clone): keep Shift+click copies at the part spacing
The coarse bounding-box pass only stopped at obstacles whose box lay in
the push path, so a copy could drop past a neighbor beside the path and
end inside its spacing. A box push now also stops at an obstacle nearer
than the spacing to the side of the path.

A push ignores a part the copy starts on, so a settle could slide out of
that part and stop clear of it yet inside its spacing. SettlePlacement
now prefers a push order that keeps the part spacing, and a named order
that ends too close falls back to the other order.

Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
2026-11-13 15:43:47 -05:00
ajandClaude Opus 5.5 fa6781d8b1 fix(options): name clone push orders by axis, not direction
The labels said left and down, but every push follows the plate quadrant:
on quadrant 4 "Push left, then down" pushed left, then up.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-11 14:03:31 -05:00
ajandClaude Opus 5.5 cafb34b510 feat(clone): choose Shift+click push order and add box-only Ctrl+click
Shift+click in Clone Parts always kept whichever axis order landed the
copy nearest the origin, which can park it in a pocket the user didn't
want. Options > Clone push placement now picks Closest to origin (the old
behavior, still the default), Push left then down, or Push down then left.

Ctrl+click settles the copy on bounding boxes alone, so it stops square
to its neighbors' boxes instead of nesting into their shapes. Shift+click
keeps its box pass then geometry settle; both follow the chosen order.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-11 07:53:24 -05:00
ajandClaude Opus 5.5 5eb7fd920b fix(slide): let a part slide along a neighbor touching it through PEP rounding noise
Six-decimal incremental PEP programs round arc centers, so an arc's end
tangent misses its neighbor's by about gap / radius (1.6e-5 rad on the
offset 5/32" fillet in the reported nest). Two parts resting one spacing
apart then gave the slide contact a Minkowski cone a hair wider than a
half-plane, which the classifier read as the whole plane: every direction
blocked, so the top part could not be pushed sideways along the part below.

SlideContact now reads a cone up to TangentSlack (1e-4 rad) past a
half-plane as a noisy half-plane and widens its boundary and concave-ray
comparisons by the excess, so near-tangential slides read as tangential.
A direction admitted that way can enter material by at most travel x
excess at that contact, and every other contact is still classified on its
own; wider cones remain real overlap and block. Raising JointTolerance was
not needed for this case and is left at 1e-6.

Whole-job benchmarks (synthetic nests plus the PEP job at 3 and 60 parts,
--parallel 1) are identical before and after for every engine.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-05 21:13:54 -05:00
ajandClaude Opus 5.5 0547af2ff6 fix(nudge): always move the full calculated step
Interlocked rows, such as staggered triangles, cannot slide straight past
their neighbors, so capping the step with a push left them unable to
pattern down. The calculated step now moves the full distance like a fixed
nudge, even off the plate or onto a part; the layout check reports either.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-04 22:42:53 -05:00
ajandClaude Opus 5.5 d98bee87ec feat(nudge): step the selection by a calculated distance
Set Offset Increment gains a "Calculated distance" option. With it on, the
arrow keys move the selection by its own size plus the part spacing,
measured on its geometry like a fill's copy distance, so it lands tight
without a push back. The move stops early at an edge, clamp or part, and a
clone preview steps clear of the copy just placed.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-04 22:21:56 -05:00
ajandClaude Opus 5.5 b8e8cc387d fix(geometry): let parts push off a frame whose contour misses closing by 1e-6
PEP-rounded drawings can leave a contour 1e-6 short of closing. ShapeBuilder
chains it as a loop at Tolerance.ChainTolerance, but the slide classifier
re-recovered loops at 1e-7, so the whole part became unresolved and every
contact with it blocked. Parts placed in its cutout at exactly the part
spacing could not be pushed (Y/X keys) in any direction, even away from the
wall. Recover loops with the same tolerance ShapeBuilder uses.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-28 14:03:38 -04:00
aj 8628c69098 fix(ui): settle shift-click cloned parts with repeated directional pushes 2026-10-08 18:57:39 -04:00
aj 2b78fb3a75 fix(geometry): resolve blocking contacts across directional slide paths 2026-09-27 23:24:31 -04:00