N26-295's PT42 pairs saved spacing in slice 1 but every shared edge was
still cut twice, costing a pass per edge and risking a freed part
tipping under the head on the second pass.
Plan Cutting now cuts a plate's common lines once unless the plate is set
to cut them twice. Each group is cut member by member, owner before
partner (a captured dependency that search and replay enforce, so a kept
order cutting the partner first is a constraint conflict): the member's
holes, then the shared cuts it owns as open CommonLine centerline cuts
entered through the notch on the span's axis, then its remainder pieces,
each ramped in from the kerf the shared cut opened. Capture marks the
shared spans as tabs on the owned clean copy, so replay's contour
accounting proves each perimeter is cut exactly once; a lead that fits
at neither end refuses as UnsupportedGeometry naming the span, never
shortened. Material still comes from the drawing, so utilization,
quantity and overlap results do not change. Members are never
support-tabbed; locked or excluded members and broken groups refuse.
The CI Fiber post writes shared cuts in the cut-off form with a lead-in
and no G41/G42, and remainders in the contour form on their perimeter's
compensation side, named by a remainder comment. Cincinnati CL (whose
PreApplied mode offsets nothing) and Gravograph refuse such nests, as do
the desktop and console for any post without ICommonLinePostProcessor;
nothing falls back to a silent double cut. Plate > Arrange > Cut Common
Lines Twice keeps slice 1's behavior, persists with the plate and makes
an open plan stale.
Pre-post review now checks each span is cut once, on its centerline, by
the member cut first, and the rapid check treats a finished member's
remainders as an obstacle. Compensation start in void and cancel in
kerf are unconfirmed on the CI FIBER 4020; release waits on a 3/16
stainless coupon trial.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A display perimeter written without its own tag reloaded as an ordinary
cut, so a saved blank would come back with its outline to be cut. Programs
now carry it as :DISPLAYPERIMETER and the reader maps it back, and stored
source entities keep the DISPLAY PERIMETER layer so editing the drawing
rebuilds the same never-cut outline.
Builds older than this read the unknown tag as a cut. Open nests with
display perimeters only in builds that include this change.
A hole can now be declared a tabbed cutout in the CAD Converter: pick a
circle or any edge of a closed hole, set the tab count and width, and drag
the tabs around the hole. The definition persists on the drawing and in the
nest file, and stays editable from the source entities.
The builder replaces the hole with open cut pieces and uncut spans on a new
Tab layer. Tabs are material, so area, nesting and overlap checks still see
a closed hole, but they are never cut. Plan Cutting and Assign Lead-ins cut
each piece from the slug with the internal lead-in and no lead-out. A lead
that would reach back over a tab is mirrored, and an arc lead onto an arc
pierces straight in. Planning accounts for each span between tabs and runs
the open-cut proof, so its own tabbed cutouts certify; tabs followed by a
lead-out are still refused. Pre-post review flags programs that still
contain tab motions.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Breakoffs are now picked by their joining line, default to the smaller side as scrap
(flippable), and cut that line between tabs on a new Break layer instead of slots.
Plan Cutting and Assign Lead-ins enter each cut from the scrap with the nest's internal
lead-in, or pierce on the line without one; checks treat break cuts as intentional open
cuts that are not material.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Repo-wide sweep with the pinned CSharpier 1.3.0 tool. Whitespace and
line-wrapping only; OpenNest.Engine.Tests (109) and OpenNest.IO.Tests
pass after reformat, full solution builds 0 errors.
Added .csharpierignore so csproj/config XML keeps its existing layout
(CSharpier's XML wrapping churns attributes with zero benefit).
Formatting is now enforceable: dotnet csharpier check . passes.
ProgramReader now supports G-code user variables with a two-pass
approach: first pass collects variable definitions (name = expression
[inline] [global]) and evaluates them via topological sort and
ExpressionEvaluator; second pass parses G-code lines with $name
substitution and VariableRef tracking on motion and feedrate objects.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Move DxfImporter, DxfExporter, NestReader, NestWriter, ProgramReader,
and Extensions into a new OpenNest.IO class library. The WinForms project
now references OpenNest.IO instead of ACadSharp directly.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
ajandClaude Opus 5.5