N26-295's PT42 pairs saved spacing in slice 1 but every shared edge was
still cut twice, costing a pass per edge and risking a freed part
tipping under the head on the second pass.
Plan Cutting now cuts a plate's common lines once unless the plate is set
to cut them twice. Each group is cut member by member, owner before
partner (a captured dependency that search and replay enforce, so a kept
order cutting the partner first is a constraint conflict): the member's
holes, then the shared cuts it owns as open CommonLine centerline cuts
entered through the notch on the span's axis, then its remainder pieces,
each ramped in from the kerf the shared cut opened. Capture marks the
shared spans as tabs on the owned clean copy, so replay's contour
accounting proves each perimeter is cut exactly once; a lead that fits
at neither end refuses as UnsupportedGeometry naming the span, never
shortened. Material still comes from the drawing, so utilization,
quantity and overlap results do not change. Members are never
support-tabbed; locked or excluded members and broken groups refuse.
The CI Fiber post writes shared cuts in the cut-off form with a lead-in
and no G41/G42, and remainders in the contour form on their perimeter's
compensation side, named by a remainder comment. Cincinnati CL (whose
PreApplied mode offsets nothing) and Gravograph refuse such nests, as do
the desktop and console for any post without ICommonLinePostProcessor;
nothing falls back to a silent double cut. Plate > Arrange > Cut Common
Lines Twice keeps slice 1's behavior, persists with the plate and makes
an open plan stale.
Pre-post review now checks each span is cut once, on its centerline, by
the member cut first, and the rapid check treats a finished member's
remainders as an obstacle. Compensation start in void and cancel in
kerf are unconfirmed on the CI FIBER 4020; release waits on a 3/16
stainless coupon trial.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Pinned-lead and locked-lead warnings named a Drawing Pins Off command and a
Clear Lead-ins command that the desktop does not have; name Plate > Remove
Lead-ins and spacing instead. Closing Plan Cutting no longer claims nothing
changed after lead-ins or cut-offs were cleared, the no-stock reason no
longer says the part is larger than every sheet when only the usable area at
the checked rotations is too small, and the console says whole-job engines.
Capture now honours a placement's pins only while they are active: a part
with DrawingPinsOff plans from the plate settings with no warning (D1's
per-part escape hatch), and Part.HasActiveDrawingPins is the shared test.
A pinned part is regenerated like any unlocked part whatever lead-ins or
settings it carried. A locked part with active pins keeps its exact program
and warns "Locked lead-ins override drawing pins on part N; Clear Lead-ins
to apply the pins." instead of being refused; an unlocked part a caller left
ineligible warns that its pins are not applied.
Apply's freshness record now holds each drawing's pin list (reference and an
explicit StateFingerprint of every pin's point, leads and tab) and each
part's pins-off flag, so editing either after capture returns Stale. The
fingerprint writer is shared between settings and pins; a reflection test
pins ContourCutPin's public surface to what the fingerprint covers.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
PreparedContours.Capture(program, parameters, pins) takes CutPinResolver
results for the same contours and fixes every resolved pin's contour: its
one and only entry is the pin's point, and it is emitted through the
existing emitter with the pin's own lead-in, lead-out and tab (angle
rounding off, so the entry never moves). Every catalogue returns the pinned
entry alone and emission refuses any other entry for that contour, so no
search path can relocate it. The certified tab size is the pinned outside's
own, so a pinned tab gap is genuine and replay certifies it. Unpinned
contours keep the shared settings and automatic selection; without pins the
existing preparation is untouched (5.1 digests unchanged).
Capture now resolves a regenerated part's drawing pins. A pin that does not
resolve (not on a contour, on several, sharing one, or unplaceable) is never
guessed: its contour stays automatic and the plate gets a FixedLead warning
naming the pin, making the proposal UNVERIFIED. A tab pinned on an internal
contour cannot be cut as pinned (only the outside is tabbed) and warns the
same way. Pins-off, locked parts with pins and freshness follow in 5.4.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
ajandClaude Opus 5.5