Full circles now take InternalLeadIn/InternalLeadOut like every other
cutout; the ArcCircle lead settings and the cutting panel's Arc / Circle
tab are removed. Circle-specific geometry handling (radius clamp, angle
rounding, pierce zone) is unchanged.
Older nest files and desktop settings still load: their arcCircleLeadIn/
arcCircleLeadOut keys are ignored and no longer written, so re-planned
circles take the internal leads. Saved part programs are untouched.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Plan Cutting is now the only automatic lead-in assignment, and parts the
support grid cannot hold level are reported wherever they lack a
steadying tab.
- Remove Assign Lead-ins (plate and nest), LeadInAssigner, the lead-in
tool's Auto-Assign button and the Auto Tab size range; old settings
with autoTab sizes still load
- Manual Place Lead-in tabs the clicked entry when support tabs are on
and the grid cannot hold the part (SupportTabSettings)
- New PartSupport finding: Plan Cutting replay and best-effort plans
warn when a drawing pin, a lead-in that does not fit or no single tab
leaves a part unsteady; the pre-post review checks each placed
program's outside tab gap. These warnings replace the advisory
weak-tab notes; only the inside-corner tab note stays advisory, and
never for a pin
- Pinned perimeters keep their pin but carry the support analysis
- Draw grid points as pixel-snapped squares without anti-aliasing
- Post fixtures build lead-ins through a test-only TestLeadIns helper
- Docs: support tabs, pre-post verification and planner notes
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Model the machine's support bed as a grid of contact points measured
from the plate origin, and check each part's center of gravity against
the convex hull of the grid points under its material. The bed is
extensible so straight and CAD-imported curved slats can follow.
- Core: SupportBed/SupportGrid, SupportMaterial and SupportAnalyzer
(margin with registration tolerance, best single tab point)
- Nest-wide support bed that every plate follows, saved in
plateDefaults.supportBed; machine defaults in support-grid.json
- CuttingParameters.SupportTabs: Plan Cutting tabs only unsupported
parts and limits their perimeter entries to points where the tab
steadies the part, falling back to any fitting entry
- Desktop: Nest > Support Grid..., View > Draw Support overlay and a
"Tab parts the support grid cannot hold level" tab option
- docs/support-tabs.md, nest file format and planner notes
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Console --plan-cutting and MCP plan_cutting/apply_cutting_plan run the
desktop's CuttingPlanBatch: capture, plan, then an all-or-nothing apply.
Settings come from an explicit JSON file or the plates' identical saved
settings, never defaults. Unverified plans need per-call acceptance,
which is not posting consent. Console --no-fill plans a loaded nest as
is; a blocked plan exits 2 and saves nothing. Scrap cut-offs stay
desktop-only.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Thick plate pierces leave a crater wider than the kerf. CuttingParameters.PierceDiameter
(Cutting Settings > Pierce Diameter, 0 = off) requires every lead-in pierce to keep half
of it from all part material: its own contour, its holes and every other part.
- LeadPathValidator checks the zone during Plan Cutting candidate checks and final
replay; fixed emissions warn as usual. No-fit findings explain the zone.
- PierceZoneReview reports Pierce zone warnings before posting for leads from any source.
- Holes whose configured pierce is inside the zone move it toward the hole's PolyLabel
pole (round holes: the centre), as close to the contour as the zone allows; a hole
too small for the zone is pierced at its pole and the shortfall is still reported.
- Straight corner leads and round-hole clamping use the larger of PierceClearance and
the zone radius. The manual lead-in preview shares the Core rules.
- Persisted through the DTO, owned copies and state fingerprint.
Perimeter fallback is not included; see docs/geometry/pierce-zone.md.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Drawing cut pins and the per-placement pins-off flag now survive
save/reload and travel in drawing packages.
- `DrawingDto.cutPins` reuses the plate cutting-parameter lead and tab
DTOs. Pins are read strictly per entry: an unknown lead or tab type is
never replaced by a default, because a pin that cut differently from
what was saved is worse than no pin. A bad entry is skipped with a
reader warning naming the drawing and pin, and the rest load; a value
that is not a list loads no pins, with a warning. A nest never fails to
open over pins.
- `PartDto.drawingPinsOff` is written only when true. Anything other than
a boolean loads as pins on (the drawing wins, D1) with a warning naming
the plate and part, so an operator's override is never lost silently.
- Packages carry pins as drawing content, so pinning a drawing changes
its package hash and the newer-revision notice can tell geometry/pins
changes from detail-only ones.
- `Part.DrawingPinsOff` holds the flag; nothing plans with it yet.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
ajandClaude Opus 5.5