Clamps could only sit on the origin-side edge and be edited as a list in
Nest > Clamps. Setting them up against a real sheet is easier by dragging
them where they are, so Plate > Edit Clamps adds an edit mode: drag a clamp
along its edge or onto another edge, click near an edge to add one, click a
clamp's locating dimension to type its distance from the origin, Delete to
remove. Dimensions measure to the clamp center or its near edge
(remembered per user). Edits replace the nest's rail so every sheet follows,
like the dialog.
Rail clamps now carry a ClampEdge (origin side, far side, origin end, far
end), positioned from the origin along that edge. Origin-side clamps keep
their ids and files; other edges persist in optional per-edge arrays in
.nest files and clamps.json, omitted when empty.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Slice 3b task 1 (D8/D9): ClampRail gains RemovalMinutes (D9, default
5 minutes, validated finite >= 0) and Plate gains RemovedClamps (rail
clamp ids taken off this sheet as a last resort) plus the computed
ClampRemovalMinutes. Plate.SetClampRail gains an overload that
attaches a rail with a removed-clamp set; zones become the rail's
resolution for the sheet minus those ids, re-resolved on every
resize/rotate so a removed clamp stays off and reappears removed if a
later resize brings it back onto the sheet. ClampRail.Matches gains an
overload comparing against the reduced resolution.
IO: PlateDto.RemovedClamps and ClampRailDto.RemovalMinutes persist
(missing removalMinutes falls back to the default; missing
removedClamps means none). The writer's empty-plate drop logic no
longer drops a sheet whose only content is a removal state the
defaults can't recreate. The reader re-attaches the nest rail to a
plate only when its saved zones equal the rail's resolution minus its
saved removed ids, so a reduced-clamp sheet keeps following the rail
(and the removal) through later resizes instead of freezing as static
zones.
Engine/desktop wiring (minimal-removal computation, Auto Nest
last-resort removal, cut-time, UI) is Slice 3b tasks 2-3, not yet
done.
Tests: 16 new Core (ClampRailTests) + 5 new IO (ClampRailPersistenceTests)
covering validation, resize/resolve behavior, round-trip, legacy
missing-key defaults, and the empty-plate-with-removal-only retention
case. Mutation check (reverting the RemovedClamps subtraction) turns
3 Core + 2 IO assertions red, confirming real coverage.
Gates: Release OpenNest.Tests 3884 passed/31 skipped, OpenNest.IO.Tests
105 passed, OpenNest.Engine.Tests (Clamp filter) 98 passed; scoped
dotnet format --verify-no-changes clean.
A clamp is an avoidance area, so a clamp that only partly reaches a
sheet (for example centered at 60.5" on a 60" sheet, or near the
origin) now keeps its whole 1.5" x 0.625" footprint instead of being
clipped to the sheet; clamps wholly beyond the sheet are still left
off. Job validation accepts a zone that hangs past the sheet edges and
still rejects one that does not reach the sheet at all. Both packing
lanes already block keep-outs extending past the bin; a hanging-clamp
solve through Rectangles, Irregular and Default keeps every part clear
of the whole inflated footprint.
User decision 2026-10-12, settling the plan's pending D2 question.
Add ClampRail: identical clamps (width along the edge, depth into the
sheet) at X centers measured from the plate origin on the origin-side
edge. It resolves onto any sheet size and quadrant without re-scaling:
clamps wholly beyond the sheet are skipped, one still reaching onto it
is clipped to it, and ids follow rail position (clamp-N) so a physical
clamp keeps its id on every sheet.
A plate can follow a rail (Plate.SetClampRail); its ClampZones are then
derived and re-resolved whenever Size or Quadrant changes, because the
clamps are fixed to the machine. Plates without a rail keep explicit
zones unchanged. Nest.PlateDefaults.ClampRail is the template new plates
follow, and Nest.SetClampRail applies a nest-wide rail to every plate
(an empty rail removes it).