Cutting-planning, diagnostics and fill tests drew the same circles,
squares, clockwise rectangles, closed polygons, rounded rectangles and
right-midpoint rectangle contours in private helpers. They now use
TestHelpers; files whose helper had its own default size keep a
one-line wrapper for it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The repo mixed variants such as center/centre and color/colour, so a
name could be spelled either way and searches missed half the hits.
Standardize on the US spelling, matching .NET's own APIs (Color, Center).
Wire values owned by other systems keep their spelling: the material
ledger's "Cancelled" hold status and GitHub's "cancelled" job status.
No behavior change beyond the spelling of a few status messages.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Plan Cutting ranked a convex corner first, but a corner rounded by a small
fillet had no corner vertex: its tangent joints ranked level with straight
edge midpoints, so travel decided and a large part (P230323-02 plate 8,
PT06, 0.015 corner fillets) started in the middle of a 64-inch edge. A start
there can leave a step where the cut closes after the head has put heat into
the plate; at a corner it is hidden.
A convex fillet tangent to straight edges at both ends, turning less than a
half circle and reaching no further along either edge than its length, now
makes its two joints convex-corner entries. Each carries its reach from the
sharp corner it rounds, so ranking counts it on both sides of that corner.
Longer curves, half-circle ends and inside fillets keep their tangent joints.
Every perimeter on that plate now starts at a corner; the problem-nest corpus
has no plate below its baseline.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A hole can now be declared a tabbed cutout in the CAD Converter: pick a
circle or any edge of a closed hole, set the tab count and width, and drag
the tabs around the hole. The definition persists on the drawing and in the
nest file, and stays editable from the source entities.
The builder replaces the hole with open cut pieces and uncut spans on a new
Tab layer. Tabs are material, so area, nesting and overlap checks still see
a closed hole, but they are never cut. Plan Cutting and Assign Lead-ins cut
each piece from the slug with the internal lead-in and no lead-out. A lead
that would reach back over a tab is mirrored, and an arc lead onto an arc
pierces straight in. Planning accounts for each span between tabs and runs
the open-cut proof, so its own tabbed cutouts certify; tabs followed by a
lead-out are still refused. Pre-post review flags programs that still
contain tab motions.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Breakoffs are now picked by their joining line, default to the smaller side as scrap
(flippable), and cut that line between tabs on a new Break layer instead of slots.
Plan Cutting and Assign Lead-ins enter each cut from the scrap with the nest's internal
lead-in, or pierce on the line without one; checks treat break cuts as intentional open
cuts that are not material.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
AutomaticEntryCandidatesWithFallbacks completes the uncapped catalogue
with tier-3 fallbacks after the preferred points: native arc midpoints,
the eight compass points of a whole circle (a pure-circle contour is now
usable instead of refusing), near-convex-corner points on each incident
straight edge back from the corner by 2 x the applicable lead-in length
using the emitter's own SelectLeadIn semantics (non-length lead-in styles
contribute 0 and the fallback is omitted, never approximated), and the
exact target-facing closest point toward the caller's look-ahead. Every
fallback runs through the same reflex/cusp exclusion — a raw closest
point or an inset landing on a forbidden inside corner is dropped — and
the same geometric duplicate merge; short edges omit an out-of-segment
inset by projection parameter instead of extrapolating. No ranking and
no lead-safety verdict yet.
Internal PreparedContours.AutomaticEntryCandidates builds the uncapped
preferred start catalogue per contour from the contour's own winding:
convex corners, then straight-edge midpoints, then line/arc tangent
joints, deduplicated geometrically with the preparation epsilon (the
most preferred metadata wins at equal points). Reflex and cusp vertices,
collinear splits and circles are never enumerated for automatic placement;
hole slugs classify from their own travel. Manual Entry/ClosestEntry and
the legacy Entries API are unchanged; emission wiring comes in S09.