N26-295's PT42 pairs saved spacing in slice 1 but every shared edge was
still cut twice, costing a pass per edge and risking a freed part
tipping under the head on the second pass.
Plan Cutting now cuts a plate's common lines once unless the plate is set
to cut them twice. Each group is cut member by member, owner before
partner (a captured dependency that search and replay enforce, so a kept
order cutting the partner first is a constraint conflict): the member's
holes, then the shared cuts it owns as open CommonLine centerline cuts
entered through the notch on the span's axis, then its remainder pieces,
each ramped in from the kerf the shared cut opened. Capture marks the
shared spans as tabs on the owned clean copy, so replay's contour
accounting proves each perimeter is cut exactly once; a lead that fits
at neither end refuses as UnsupportedGeometry naming the span, never
shortened. Material still comes from the drawing, so utilization,
quantity and overlap results do not change. Members are never
support-tabbed; locked or excluded members and broken groups refuse.
The CI Fiber post writes shared cuts in the cut-off form with a lead-in
and no G41/G42, and remainders in the contour form on their perimeter's
compensation side, named by a remainder comment. Cincinnati CL (whose
PreApplied mode offsets nothing) and Gravograph refuse such nests, as do
the desktop and console for any post without ICommonLinePostProcessor;
nothing falls back to a silent double cut. Plate > Arrange > Cut Common
Lines Twice keeps slice 1's behavior, persists with the plate and makes
an open plan stale.
Pre-post review now checks each span is cut once, on its centerline, by
the member cut first, and the rapid check treats a finished member's
remainders as an obstacle. Compensation start in void and cancel in
kerf are unconfirmed on the CI FIBER 4020; release waits on a 3/16
stainless coupon trial.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Some jobs cut only cutouts into a supplied blank, such as instrument holes
in a purchased door that is the whole sheet. Its outline has to be known
to the planner (the blank is material that leads, rapids and cut-offs must
respect) but must never be pierced, led or cut.
A new DisplayPerimeter layer marks that outline. It is material, so
nesting, containment, lead clearance and automatic cut-offs all see the
blank; a door that fills its sheet leaves cut-offs nothing to cut. Cutting
preparation keeps it out of the contours entirely: with no cut perimeter
every contour is a hole with internal leads, and the search, best-effort
and safest-route paths stop offering a perimeter. Replay refuses any run
along the display perimeter and completes once every other ring is cut.
A display perimeter must be one whole closed contour enclosing every other
contour; a mixed ring, one inside another contour, or a second one is
refused with that reason. Saving, drawing and posting it are still to do.
A hole can now be declared a tabbed cutout in the CAD Converter: pick a
circle or any edge of a closed hole, set the tab count and width, and drag
the tabs around the hole. The definition persists on the drawing and in the
nest file, and stays editable from the source entities.
The builder replaces the hole with open cut pieces and uncut spans on a new
Tab layer. Tabs are material, so area, nesting and overlap checks still see
a closed hole, but they are never cut. Plan Cutting and Assign Lead-ins cut
each piece from the slug with the internal lead-in and no lead-out. A lead
that would reach back over a tab is mirrored, and an arc lead onto an arc
pierces straight in. Planning accounts for each span between tabs and runs
the open-cut proof, so its own tabbed cutouts certify; tabs followed by a
lead-out are still refused. Pre-post review flags programs that still
contain tab motions.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Breakoffs are now picked by their joining line, default to the smaller side as scrap
(flippable), and cut that line between tabs on a new Break layer instead of slots.
Plan Cutting and Assign Lead-ins enter each cut from the scrap with the nest's internal
lead-in, or pierce on the line without one; checks treat break cuts as intentional open
cuts that are not material.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Every nesting-geometry consumer filtered only rapids, so scribe/etch
moves counted as part material. An etch tick that ends a hair outside
the outline (PEP bend ticks start on the notch edge) made the part
"open geometry leaving the material region": the job validator threw
and every built-in engine plus Gpt6Astra crashed on real PEP jobs
(PT75, drawing 4980 A01 PT77). Marks are only on the surface, so they
should never affect placement, collision, area, or validation.
- SpecialLayers.IsMaterial excludes Rapid and Scribe; used by drawing
area, canonical angle, part collision, PartGeometry, plate perimeter,
best-fit/pair evaluation, rotation analysis, GPU evaluators, and both
validators. Timing, display, splitting and posts still see marks.
- ConvertGeometry also maps the saved SCRIBE layer name to Scribe, so
programs rebuilt from stored entities keep their marks.
- NestReader repairs older files (e.g. PepNestExport output) whose
programs saved etch as cut moves while source entities kept SCRIBE.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Restructure the cutting parameters dialog with separate Lead-In and
Lead-Out GroupBoxes per tab, exposing editable length/angle/radius
fields for lead-outs (previously hardcoded). Add Tabs section with
enable checkbox and width control. Also fix lead-in/lead-out angle
calculations and convert cutting strategy output to incremental mode.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
ConvertProgram.ToGeometry() created entities without setting Color,
defaulting to Color.Empty (alpha=0). After ededc7b switched from
Pens.White to per-entity colors, these rendered fully transparent.
- Add explicit colors to all SpecialLayers (Cut=White, Rapid=Gray, etc.)
- Set entity Color from layer in ConvertProgram for lines, arcs, circles
- Add GetEntityPen fallback: treat Empty/alpha-0 as White
- Add bend line rendering and selection in EntityView/CadConverterForm
- Fix SolidWorksBendDetector MText formatting strip for bend notes
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Move all projects from Source/ to repository root for simpler navigation.
- Remove External/ dependency DLLs (will use NuGet packages)
- Remove Installer/ NSIS script
- Replace PartCollection/PlateCollection with ObservableList
- Add packages.config for NuGet dependencies
🤖 Generated with [Claude Code](https://claude.com/claude-code)
Co-Authored-By: Claude <noreply@anthropic.com>
ajandClaude Opus 5.5