The Layout label counted parts off the plate or inside the edge spacing, but
nothing showed which part or where, so the user had to hunt for it. Each edge
finding now gets a canvas marker like the overlap and spacing ones: a red
crosshair where a part leaves the sheet and an orange ring at the gap to the
edge, in every visible display mode, with hover text that carries the finding's
message. Markers are retained across edits like the other overlay findings
(only a changed part's marker drops), and a sheet size, edge spacing or outline
change clears them. Validate Nest already located these findings through
PostVerificationFinding.Location.
"Near edge" / "inside the edge spacing" read as a spacing rule rather than a
placement problem, so the label, overlay messages, PlateEdgeReview findings
and the Validate Nest category now say the part is outside the work area. Off
the plate keeps its wording. The PostVerificationKind.EdgeSpacing name stays.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The status bar's "Layout: OK" ran its own snapshot check of overlaps and
part spacing, separate from Validate Nest and posting, so a part dragged
off the sheet still read OK.
The plate capture now owns the sheet frame (sheet box, work area,
outline), and the worker runs PlateEdgeReview's material check on it:
"N off plate" and "N near edge" join the label. Snapshots hold no leads,
so leads past the sheet stay a Validate Nest/posting finding. The
geometry stamp now includes edge spacing and outline so changing them
marks the result out of date. Bare-part captures (Plan Cutting) have no
frame and are unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Expensive alloy jobs (N26-295, 310 stainless) could not fit their last
PT42 at full part spacing; the plate was squeezed to 0.2 spacing with a
part 0.14 from the edge. Parts whose straight edges face each other one
kerf apart are cut on the same centerline, saving the spacing along each
shared edge.
Plate.CommonLines holds groups of parts and the kerf they were joined
at. Shared spans are derived from the placed clean perimeters, never
stored, so a moved member breaks its group instead of leaving a stale
span. Plate > Arrange > Join Common Line slides the selected parts
together at the plate's kerf; Remove Common Line ungroups them. The
plate draws shared spans as a dashed centerline.
Both spacing checks hold group members to the kerf instead of the part
spacing, and a new pre-post Common lines check reports broken groups, a
changed kerf, and leads that run into a partner. Groups persist as part
positions in an optional commonLines array that older readers ignore.
This first slice still cuts every shared edge twice; single-pass cutting
through Plan Cutting and the posts comes next.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The overlap check now runs the pre-post part spacing scan on its snapshot,
so the canvas label and posting agree. Too-close pairs are counted in the
label and marked with an orange ring showing the gap, with hover details.
A fully checked plate with no findings draws a green check instead of
text; the status bar keeps the wording. Changing the plate's part spacing
now stales the report, and repeated parts share one offset outline so
automatic rechecks stay fast.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Trim refused the piece between two crossing cut-offs because a cut-off had
one start and one end, so a line could not be stopped short around a pocket
of parts without deleting it and drawing two. A cut-off now carries Gaps,
stretches between its limits left uncut: segment generation excludes them
like parts, so the line splits into segments that each take their own place
in the cut sequence. Trimming a middle piece adds a gap from one crossing
centre to the other (merged with any it touches), Extend near a gap's edge
closes it, and Swap Through-Cut refuses a junction a gap touches rather
than guess which side of the gap should run through.
Every reader of the limits treats a gap as uncut, so nothing waits for,
warns about or credits a cut that never happens: segment spans stop at a
gap, the cutting dependencies skip a part inside one, the clamp check
ignores a clamp inside one, the cutting-state and overlap stamps go stale
when gaps change, and a gapped line is never full span for the expected
remnant or automatic cut-offs. Gaps persist as an optional gaps array;
older versions ignore it and would cut straight through.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Stock can arrive up to 1.5 in wider than nominal, so only the origin-side
edge is certain. A cut-off with a head-locked overcut cuts past the nominal
far edge with the head height locked, covering the oversize. With that lock,
Plan Cutting may start the far-edge segment at the far edge: overcut outward,
rapid back still locked, unlock, cut toward the origin. Without it the
direction stays fixed, as decided in Project Memory a20ea455.
- CutOff.HeadLockOvercut / FarEdgeFirst, persisted in .nest; HEAD HEIGHT
LOCK/UNLOCK comment markers; far edge is quadrant-aware.
- Planner offers the reversed far-edge segment in the joint search, the
safest route and segment insertion; Apply records the direction.
- Cincinnati CL and CI Fiber posts gain lock/unlock code settings and refuse
head-locked cut-offs while either is empty.
- Automatic cut-off dialog setting (off by default, 1.5 in), kept between
sessions and used for new cut-offs.
Lock codes and machine behaviour with the head locked are unconfirmed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The desktop captures the overlap freshness stamp before its error
boundary, and a null cut-off or clamp zone in the plate's lists threw
NullReferenceException there. Stamp missing entries as a distinct empty
state so the whole-plate capture can report the malformed input as a
failed check instead.
Project Memory: opennest cdbe2629-b562-46ee-9509-2b120a511654
Plate.ClampZones are stored relative to the sheet's lower-left corner,
but cut-off positions, motions and part poses use the signed quadrant
frame. The automatic cutoff planner, manual cut-off contacts, clamp
rapid warnings and whole-plate overlap capture compared the two
directly, so in quadrants 2-4 a cut or rapid through a real rail clamp
was neither avoided nor warned about.
Add ClampZoneFrame.ToPlacement, which maps live zones into the
placement frame exactly like the sheet and engine stock, and use it in
every Slice 5 consumer. It rejects missing or malformed zones (bounds
stay publicly mutable); pre-post verification reports those as an
incomplete clamp check instead of a clear result. Overlap freshness now
treats a size or quadrant change as moving the zones.
Tests use real ClampRail zones in all quadrants; the hand-signed
quadrant fixtures that hid the defect are converted to rails.
Project Memory: opennest 274836d5-fb76-4619-b3cc-0c811e767dd6
ajandClaude Fable 5.2