A Vertical or Horizontal Remnant fill of a quantity of round parts left
a deep remnant on the table: twelve 8 in. flanges took 25.6 in. of a
60 in. sheet's length and stopped 16 in. short of its far edge, where
two full-height columns need 15.1 in. Three causes:
- The low-quantity shrink scaled both sides, so stripes could not span
the side the remnant runs along. It now narrows only the trimmed axis.
- The ranking compared untrimmed counts, so the full-sheet layout always
beat the full-height columns and was then trimmed. It now ranks the
layout as it will be kept.
- The trim kept overlapping bounding boxes as interlocked pairs, which
staggered discs always are. Discs are now trimmed one by one.
The circle strategy also offers each stagger mode's stripes in both
directions to a remnant ranking. Every change is limited to remnant
fills of round parts: applied to other shapes, the trimmed ranking let
a tilted bar layout block the rest of a nest, and the disc trim moved
the Irregular engine's sample layout, so every other fill is unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The two stripe layouts differ only in how far odd stripes shift, so they are
now one StaggeredFill with StaggerMode.HalfPitch (was FillEndOdd: half-pitch
shift, odd stripes one disc fewer) and StaggerMode.SlackShift (was
FillEndEven: shift by the stripe's leftover, every stripe full). The unused
FillEngine base and its throwing Fill(item, maxCount) go away. Layouts and
orientation tie-breaks are unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The Circle fill strategy's stripe layouts (FillEndOdd, FillEndEven) now try
switching from staggered to straight stripes, a diameter apart over the last
staggered stripe, at every stripe, all staggered and all straight included,
and keep the switch that places the most; a tie stays staggered. A 9" circle
on a 60x120 sheet at 0.2 spacing now fills 89 (five staggered rows, two
straight) instead of 88.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
FillEndOdd and FillEndEven read Box.Width as the X span, though it is
the Y span, so non-square sheets got the wrong pitch. They also started
centers at the bin corner, leaving circles a radius outside it.
FillEndEven now tries both stripe directions, as FillEndOdd does.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Item.Create builds the circle packer's view of a part: the minimum
enclosing circle of its outward-flattened perimeter (padded by the
layout check's flattening allowance), its fill ratio, the offset back
to the part origin, and the largest disc clear of material inside its
cutouts. Gears and sprockets pack by their tip circle around their
bore; the fill ratio lets a future engine decide which jobs to bid on
instead of a yes/no round test.
Adds MinimumEnclosingCircle (Welzl, repeatable order) to Core geometry.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Staggered stripes were spaced only so adjacent stripes touched
diagonally. When the in-stripe pitch stretched past sqrt(3)*D, stripes
two apart, which sit directly over each other, came closer than a
diameter. Clamp the stripe spacing to at least a radius in both fills.
FillEndOdd also divided by zero when a single circle fit per stripe;
it now stacks those stripes a diameter apart. FillEndEven now clones
the template item, so placed circles keep its radius instead of zero.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Repo-wide sweep with the pinned CSharpier 1.3.0 tool. Whitespace and
line-wrapping only; OpenNest.Engine.Tests (109) and OpenNest.IO.Tests
pass after reformat, full solution builds 0 errors.
Added .csharpierignore so csproj/config XML keeps its existing layout
(CSharpier's XML wrapping churns attributes with zero benefit).
Formatting is now enforceable: dotnet csharpier check . passes.
Extract shared FillAxis helper parameterized by orientation,
eliminating 34-line duplicate between horizontal and vertical fills.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
"Length" is more natural than "height" for flat plate materials.
Renames the field on OpenNest.Geometry.Size, Box.Height property,
and all references across 38 files.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Move all projects from Source/ to repository root for simpler navigation.
- Remove External/ dependency DLLs (will use NuGet packages)
- Remove Installer/ NSIS script
- Replace PartCollection/PlateCollection with ObservableList
- Add packages.config for NuGet dependencies
🤖 Generated with [Claude Code](https://claude.com/claude-code)
Co-Authored-By: Claude <noreply@anthropic.com>