Slats are strips of a set thickness running the full length or width of
the table, one every pitch. A part's contacts are the corners of where its
material crosses a slat, so the support check and support tabs work as on
the grid. Nest > Support Bed... picks grid or slats; nest files store
type "slats" and support-grid.json keeps both layouts' values. Draw
Support shows the slats cut off to the sheet.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The assigned machine now drives the support grid, lead-ins and cut-offs, so
it should be visible without opening a menu. The status bar shows
"Machine: <name>" beside the material; left- or right-clicking it lists the
machines (the same list as Nest > Machine) above the label.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The support grid was one shared support-grid.json, off by default, and a nest
had no machine at all, so a plasma table and a fiber laser could not have
different grids, and nothing could pick machine-specific behavior later
(lead-ins differ between laser and plasma; tabbing depends on the grid).
- Nest.Machine (id + name) persists as top-level `machine` in nest.json;
malformed values load as none.
- MachineConfig.SupportGrid holds each machine's grid; a machine without one
still falls back to the legacy support-grid.json.
- New and BOM import assign the Tools > Nest Defaults machine (first by name
when none is chosen) and give the nest that machine's grid.
- Nest > Machine reassigns a nest and swaps in the new machine's grid;
Nest > Support Grid saves machine defaults to the nest's machine.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Plan Cutting is now the only automatic lead-in assignment, and parts the
support grid cannot hold level are reported wherever they lack a
steadying tab.
- Remove Assign Lead-ins (plate and nest), LeadInAssigner, the lead-in
tool's Auto-Assign button and the Auto Tab size range; old settings
with autoTab sizes still load
- Manual Place Lead-in tabs the clicked entry when support tabs are on
and the grid cannot hold the part (SupportTabSettings)
- New PartSupport finding: Plan Cutting replay and best-effort plans
warn when a drawing pin, a lead-in that does not fit or no single tab
leaves a part unsteady; the pre-post review checks each placed
program's outside tab gap. These warnings replace the advisory
weak-tab notes; only the inside-corner tab note stays advisory, and
never for a pin
- Pinned perimeters keep their pin but carry the support analysis
- Draw grid points as pixel-snapped squares without anti-aliasing
- Post fixtures build lead-ins through a test-only TestLeadIns helper
- Docs: support tabs, pre-post verification and planner notes
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A tab cannot lift a part's margin past its contacts' own hull edges, so a
whole stretch of outline often ties for the best tab point, and the first
sample found won, leaving the tab off-center. Keep the full outline search
for the margin, then among samples within Tolerance.Epsilon of the best,
pick the one nearest the line through the center of gravity across the
long side of the outline's minimum-area bounding rectangle. A part held
only near one end is still tabbed at the far end.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The best tab point used to land in inside corners: equally good points
run along a straight edge, vertices were tried first and the first tie
won. Operators cannot grind a nub flush there.
- SupportAnalyzer finds inside corners (inward-turning vertex runs of at
least 30 degrees, so chorded fillets count) and keeps tab points a
clearance from them; of equally good points it picks the one farthest
from an inside corner. Plan Cutting and the overlay use twice the tab
size; AcceptsTabAt rejects closer points
- When no steadying entry has a lead-in that fits, the search falls back
to entries clear of inside corners, then to every entry, each ordered
by how well the tab steadies the part, keeping only the steadiest that
fit
- Replay notes parts whose planned tab cannot hold them level or sits in
an inside corner; the notes are advisory and leave a Ready plan Ready
- Console/MCP plate summaries print a ready plan's notes
- docs/support-tabs.md and cutting-planner notes
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Model the machine's support bed as a grid of contact points measured
from the plate origin, and check each part's center of gravity against
the convex hull of the grid points under its material. The bed is
extensible so straight and CAD-imported curved slats can follow.
- Core: SupportBed/SupportGrid, SupportMaterial and SupportAnalyzer
(margin with registration tolerance, best single tab point)
- Nest-wide support bed that every plate follows, saved in
plateDefaults.supportBed; machine defaults in support-grid.json
- CuttingParameters.SupportTabs: Plan Cutting tabs only unsupported
parts and limits their perimeter entries to points where the tab
steadies the part, falling back to any fitting entry
- Desktop: Nest > Support Grid..., View > Draw Support overlay and a
"Tab parts the support grid cannot hold level" tab option
- docs/support-tabs.md, nest file format and planner notes
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
ajandClaude Opus 5.5