A nest with no material, grade or thickness now takes them from the
library record instead of warning that the drawing differs and dropping
its cut pins. The machine's spacing and cut-off settings follow. Later
drawings still get the usual difference warning, and drawings from files
carry no thickness, so they leave the nest blank.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Plate > Set as Default and Nest > Edit's Defaults tab only changed the
open nest, so new nests never picked up the values. Set as Default now
also saves the new-nest defaults, and the Defaults tab gains an opt-in
"Use these defaults for new nests" check.
Machine thicknesses can now set part and edge spacing. A nest takes them
when its material, grade, thickness or machine changes and when a release
creates it; BOM import seeds its groups from them. Spacing edited in the
same dialog stays, and only an untouched trailing sheet follows.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Edits in the Cutting Parameters dialog only reached user settings, while a
plate's stored parameters took priority, so a change was lost on any
planned plate unless Apply succeeded. User settings now win; a plate's own
are the fallback when none are saved or readable.
WinForms tests saved to the real user-settings.json, and with user settings
winning a test's lead-ins would feed real planning, so they now use a temp
file and skip the legacy settings carry-over.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Machine Configuration held one lead-in and lead-out per thickness and
applied it to every contour. Each thickness now has Outside Cuts and
Inside Cuts tabs; inside cuts follow the outside leads until "Same as
outside cuts" is cleared, and configurations without inside leads keep
applying one pair to both.
The lead type lists, per-type fields and preview from Cutting Settings
are now a reusable LeadsEditor control that both dialogs use. The
machine tabs hide what the configuration cannot hold: the arc sweep,
the clean-hole kerf (taken from the thickness) and Line + Line.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Plan Cutting saved its settings only on a successful Apply, so a plate
that would not plan lost them. Each open then laid the machine's leads
back over the last parameters, and the cutting panel rebuilt parameters
from scratch, dropping kerf and the machine/material/thickness stamp.
Save the settings when the dialog is accepted, keep the panel's
unexposed fields, and only apply the machine's leads when the last
parameters were not already taken from that machine, material, grade
and thickness.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Curved leads turned with the contour winding, which is backwards on outside
perimeters: arc lead-ins arrived against the cut, and Line + Arc / arc
lead-outs went the long way round on one winding. LeadTurn now gives the
arc's turn direction for emission, the pierce-zone check and the preview,
and the arc geometry mirrors with it.
At convex outside corners, curved lead-ins use the first-cut edge's normal
and arc lead-outs the last-cut edge's, whichever edge was picked.
ArcLeadIn gains SweepAngle (degrees, (0, 180], default 180) in the cutting
panel, settings, nest files and cut pins; older files read as 180.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
PEP stores 3/16 as 0.188, which missed the machine's 0.1875 at the
0.0005 in tolerance; widen it to 0.001 in, still far below gauge steps.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Full circles now take InternalLeadIn/InternalLeadOut like every other
cutout; the ArcCircle lead settings and the cutting panel's Arc / Circle
tab are removed. Circle-specific geometry handling (radius clamp, angle
rounding, pierce zone) is unchanged.
Older nest files and desktop settings still load: their arcCircleLeadIn/
arcCircleLeadOut keys are ignored and no longer written, so re-planned
circles take the internal leads. Saved part programs are untouched.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Machine configurations already held a lead-in, lead-out, kerf and cut-off per
material thickness, but nothing read them: Plan Cutting and Place Lead-in
started from whatever was last applied (often another machine's or another
thickness's leads), and cut-offs used fixed view defaults. Now that nests carry
a machine, those values can be the starting point.
- MachineCuttingDefaults maps a machine's thickness settings for the nest's
material/grade/thickness onto CuttingParameters and CutOffSettings,
converting units. Clean Hole stays on holes; Line + Line is not mapped
because the configuration lacks the second segment.
- Plates without their own parameters start from the last-applied ones with
the machine's leads and kerf laid over them; plates with parameters keep them.
- The plate view's cut-off clearance, overtravel, minimum segment and direction
follow the machine on open, on Nest > Machine and after Nest > Edit.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
ajandClaude Opus 5.5