A hole can now be declared a tabbed cutout in the CAD Converter: pick a
circle or any edge of a closed hole, set the tab count and width, and drag
the tabs around the hole. The definition persists on the drawing and in the
nest file, and stays editable from the source entities.
The builder replaces the hole with open cut pieces and uncut spans on a new
Tab layer. Tabs are material, so area, nesting and overlap checks still see
a closed hole, but they are never cut. Plan Cutting and Assign Lead-ins cut
each piece from the slug with the internal lead-in and no lead-out. A lead
that would reach back over a tab is mirrored, and an arc lead onto an arc
pierces straight in. Planning accounts for each span between tabs and runs
the open-cut proof, so its own tabbed cutouts certify; tabs followed by a
lead-out are still refused. Pre-post review flags programs that still
contain tab motions.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Breakoffs are now picked by their joining line, default to the smaller side as scrap
(flippable), and cut that line between tabs on a new Break layer instead of slots.
Plan Cutting and Assign Lead-ins enter each cut from the scrap with the nest's internal
lead-in, or pierce on the line without one; checks treat break cuts as intentional open
cuts that are not material.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A drawing-pinned contour is now a fixed emission like a locked program. A
regenerated placement maps its execution motions onto the emitted contour
choices (one group per choice after the program's scribes, opened by its
rapids) and owns as fixed the lead-in, cut, lead-out and tab of every pinned
contour; the rapids between contours, including the one into a pinned
contour, stay the planner's and strictly checked. If the motions do not
split cleanly into one group per choice, nothing is treated as fixed.
So a pinned lead that meets another part's material or its own part's no
longer rejects the candidate: the feasibility precheck accepts a pinned
entry as given, the search keeps it in place, and replay reports a FixedLead
warning naming the part, cutting contour, pin and the part hit, with the
advice to increase spacing or switch off drawing pins for the part. The
plate is UNVERIFIED and needs acceptance; the lead is never shortened and
the entry never moved. The unpinned control and the same plate with pins
off are Ready.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
D1a (user, 2026-10-14): one locked cutout must not refuse the whole layout.
With confirmed parameters a locked program is now a fixed emission, accepted
as given. The replay checker and the lead validator take a per-motion owner:
a violation inside the fixed emission (a lead meeting another part's or its
own material, a rapid inside the locked program crossing a cut contour, an
uncertifiable tab gap or a partial/reversed/retraced cut) is recorded apart
instead of failing the candidate. The search never rejects or learns an order
rule from them, so fixed emissions never steer it; the planner's rapid into
the locked program and every regenerated lead keep every strict check.
Replay turns those violations into typed FixedLead findings that name the
part, contour and the part hit. A plate whose only findings are these is
BestEffort with IndependentlyReplayed set: never Ready, applicable only with
the per-proposal acceptance, and CuttingPlanService.Apply still rejects it.
Overlap, unreadable programs, stale input and cancellation still block, and
unlocked programs a caller left ineligible and the no-parameter route keep
refusing as before.
Pre-post review now re-checks locked leads against every part's clean
material, so the same violations reappear before posting.
Existing tests that encoded the old locked refusal now assert the warning;
two batch tests that used a locked crossing as their hard block use an
overlap instead. The 5.1 digests are unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Plan Cutting findings dropped the checker's geometry, so selecting one could only
zoom to part extents, and overlap-blocked plates (no preview) did nothing at all.
Findings now keep the check's world-coordinate witness (overlap regions, rapid,
contacts); selecting a row draws it with the Validate Nest overlay, on the proposal
or a blocked plate's live sheet. The witness is excluded from finding equality so
repeated search rejections still collapse to one finding.
The side panel's scrolling report was a wall of text operators skipped. It is now
a colored outcome line, one line for the shown plate, and one remedy or marker
hint above the issue grid, with secondary detail moved to tooltips.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A CuttingPlanRequest constructor overload taking a Plate made the existing
detached call new CuttingPlanRequest(null) ambiguous (CS0121). Plate scope
is now requested with CuttingPlanRequest.ForPlate, and the result summary
describes dependencies and Apply as they now behave.
The cutting planner now accepts cutoffs on plate-scoped requests and
plans whole-part prerequisites captured from owned values:
- A cutoff precedes every part its nominal span crosses, using the same
rule and drawing-reference matching as automatic sequencing; a cutoff
without a definition precedes every part. Cutoffs stay fixed programs,
need no lead-in and never become rapid obstacles; rapids into and out
of them are still checked.
- A part proven, on native clean material, to lie inside a cutout of
another part precedes that host. Touching or crossing boundaries are
ambiguous and refuse; a part in a concave pocket has no dependency.
- Both searches only expand ready parts, a preserved order that breaks a
prerequisite is a constraint conflict, and final replay rechecks the
captured prerequisites instead of trusting the search.
Plate-scoped cutting plan requests now record the plate's exact state at
capture, and CuttingPlanService.Apply installs Ready, replayed proposals
for a whole scope at once:
- Any change after capture (order, pose bits, program reference or
in-place content, drawing program, lock/lead-in flags, settings,
quantity, size, quadrant or cutoff definitions) returns Stale with
nothing changed.
- Order changes without PartAdded/PartRemoved, so drawing quantities and
sentinel plates are untouched; ObservableList.Reorder exposes the same
operation and Plate.PartsReordered is raised once per changed plate.
- Regenerated parts receive owned copies of the replayed program and of
the settings captured with the request; fixed programs stay in place.
- An install failure restores every plate exactly; an observer failure
after publication is reported as a refresh error, not a rollback.