Rotated imported arcs whose start and end radii differ by ~5e-11 are
converted without refitting their centre, so their rebuilt start point
lands just outside the cached part bounds. The allowance scaled with
coordinate magnitude (4096 steps, ~2.9e-11 here) and rejected them,
which stopped Plan Cutting's "Add scrap cut-offs" with "Converted
material extends outside cached part bounds". Use the existing 1e-10
cap as an absolute allowance; larger mismatches still block planning.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Drawings flagged CutFirst (e.g. test squares) are sequenced ahead of
every other part: they get their own route with the chosen method, then
the remaining parts follow. Cutoffs crossing a cut-first part still
precede it. The flag is editable in Edit Drawing, persists in .nest as
`cutFirst` (omitted when false) and is kept by split pieces.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
When the end tail was shorter than the minimum tail to keep, the planner
dropped the separator but still stopped the strip grid at it, so the last
strip ran to the sheet end and could exceed the maximum spacing (e.g. a
39-inch strip from 105 to 144 with 35-inch spacing). The grid now spans the
whole sheet whenever the separator is skipped, keeping every strip within
the spacing.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A cut-off line passing exactly through a vertex of the clearance outline
got duplicate intersection hits and fell back to the part's bounding box.
Automatic strip lines sit on a 0.05 lattice that often lands on such
vertices, and the strip search preferred them because the box fallback
measured as less cutting, so planned cut-offs looked box-trimmed while a
slightly moved manual line was trimmed correctly.
Slice the polygonal clearance outline exactly with half-open edges:
crossing vertices count once, touching vertices zero or twice, edges on
the line are excluded whole. Zero clearance and non-polygon outlines keep
the existing path and its conservative fallback.
Reserve nominal-line slots in the candidate lattice, compare rounded lengths in exact micro-units before pierce ties, and report real fixed-grid cut length. Per-line notices name local increases instead of negative savings. Failing-first regressions cover dense spacing, decimal ties and the legacy summary.
Plate.ClampZones are stored relative to the sheet's lower-left corner,
but cut-off positions, motions and part poses use the signed quadrant
frame. The automatic cutoff planner, manual cut-off contacts, clamp
rapid warnings and whole-plate overlap capture compared the two
directly, so in quadrants 2-4 a cut or rapid through a real rail clamp
was neither avoided nor warned about.
Add ClampZoneFrame.ToPlacement, which maps live zones into the
placement frame exactly like the sheet and engine stock, and use it in
every Slice 5 consumer. It rejects missing or malformed zones (bounds
stay publicly mutable); pre-post verification reports those as an
incomplete clamp check instead of a clear result. Overlap freshness now
treats a size or quadrant change as moving the zones.
Tests use real ClampRail zones in all quadrants; the hand-signed
quadrant fixtures that hid the defect are converted to rails.
Project Memory: opennest 274836d5-fb76-4619-b3cc-0c811e767dd6
The automatic cutoff planner tested only the proposed X against active
clamp spans, then certified a tolerance-close existing line at its own
X. A manual line just inside a clamp edge could therefore be reported
as a verified tail separator. Test the proposed X and every equivalent
existing definition before regenerating.
Also keep a same-line limited manual cut blocking the whole plan when
it lies on a clamp, as it did before clamp checks were added.
Project Memory: opennest 51597040-cff6-4304-87dc-3c2a13edf45a
The dialog buried its verdict in a scrollable text box that restated the
same numbers per plate behind a paragraph-length warning. Replace it
with:
- a bold colored status line stating exactly what Apply will do
(Ready / Blocked / No new cut-offs / Error with the reason);
- the occupied span, used span, separator X and retained tail as
compact caption+value cells with tooltips instead of four sentences;
- the warning paragraph reduced to one amber line with the full text
in its tooltip;
- a per-plate table (cut-offs, spans, tail, Ready/Blocked/No change)
for the All Plates command, replacing repeated text blocks;
- the details box now lists only issues and notices, prefixed by plate
number when planning a nest, instead of echoing every measurement.
Planning, preview, apply and rollback behavior is unchanged; tests and
the cutoffs document follow the new presentation.
ajandClaude Opus 5.5