Slice 3b task 3 (D9 + display). OpenNest.Core: TimingInfo gains
ClampRemovalMinutes (included in +, -, * so every aggregation stays
consistent); Timing.GetTimingInfo(Plate) adds plate.ClampRemovalMinutes
once per physical sheet, before the quantity multiply so it scales
with everything else cut on that sheet; CalculateTime adds it to the
estimate as a flat number of minutes regardless of the cut parameters'
unit. A plate with nothing removed is unaffected (zero).
OpenNest.Data: ClampSettings and ClampRailEditor carry RemovalMinutes
through the same three boundaries as clamp size - the rail/constructor,
the settings file (missing key falls back to
ClampRail.DefaultRemovalMinutes; present but negative/non-numeric/null
is ignored and reported Partial, same as width/depth), and
ToMachineDefaults - except it is a time, not a length, so
ConvertedTo never scales it between inches and millimeters.
Desktop: ClampsForm gets a 'Minutes to remove and replace one clamp'
field wired to the editor; PlateRenderer.DrawRemovedClamps draws each
clamp Plate.RemovedClamps lists (resolved from the full rail, since a
removed clamp is absent from Plate.ClampZones) as a dashed grey
outline with a small 'remove' marker, distinct from an active clamp's
solid hatch and still display-only - no hit test, selection or
sequencing; PlateView calls it right after the active-zone pass.
MainForm's Auto Nest completion flow lists every committed sheet with
a removal as 'Sheet N: remove clamp-X (+5 min)', using
Plate.RemovedClamps/ClampRemovalMinutes from Slice 3b tasks 1-2.
Tests: 10 new Data (ClampSettingsTests, ClampRailEditorTests) covering
round-trip/default/invalid-value handling and the never-scaled-by-units
rule; 4 new Core (TimingTests) covering the per-sheet add, the quantity
scaling, CalculateTime, and nest-level aggregation across plates.
Desktop changes (dialog field, renderer, Auto Nest summary) are
compile-verified only (-p:EnableWindowsTargeting=true), matching the
project's existing WinForms testing bar - no automated UI test exists
for the sibling DrawClampZones either.
Gates: Release OpenNest.Tests 3898 passed/31 skipped, OpenNest.IO.Tests
105 passed, OpenNest.Engine.Tests 878 passed/2 skipped; desktop and
OpenNest.WinForms.Tests cross-builds clean; scoped dotnet format
--verify-no-changes clean.
This completes Slice 3b (D8/D9) on top of Slice 3's rail-following
plates. Not published; master and other feature/clamp-zones-* branches
untouched. Windows runtime/visual acceptance not claimed - the plan's
click-through checklist (after slices 3-5) still applies.
Read clamps.json as a raw document so an explicit null is reported as
an ignored value (Partial, which the desktop warns about) instead of
being taken as an absent field. Missing or invalid sizes now fall back
to the physical 1.5 x 0.625 inch clamp expressed in the file's units,
so a millimeter file no longer gets a 1.5 x 0.625 mm clamp. Values that
would overflow when converted between inches and millimeters are
ignored and reported instead of throwing while creating a nest.
Review findings 2, 3 and 6, Project Memory 4e5f566d.
Persist the machine clamp rail in %APPDATA%\OpenNest\clamps.json, in
the same shape as the nest defaults store: camelCase JSON written with
retry, and a read that never throws. Clamps are off by default: a
missing or unreadable file keeps them off, and nothing changes until
the settings are enabled with at least one center.
Each value is read independently; an invalid one (including a single
bad clamp center) is ignored and reported as Partial so the desktop
can warn that the rail may lack a physical clamp. Values carry their
units and convert between inches and millimeters for a new nest.
aj